Automation Direct Productivity2000 P2-08ND3-1 Manual - Página 4

Navegue en línea o descargue pdf Manual para Unidad de control Automation Direct Productivity2000 P2-08ND3-1. Automation Direct Productivity2000 P2-08ND3-1 4 páginas. Dc input module provides eight 12–24 vdc sink/source inputs for use with the productivity2000 system

Imprimir página
WARNING:
To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes
vary from area to area and it is your responsibility to determine
which codes should be followed, and to verify that the equipment,
installation, and operation are in compliance with the latest revision
of these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or
operation of this equipment, or if you need additional information,
please call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
Removable Terminal Block Specifications
Part Number
P2-RTB
Number of
18 Screw Terminals
Positions
30–16 AWG (0.051–1.31 mm
Solid / Stranded Conductor
Wire Range
3/64 in (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
Conductors
"USE COPPER CONDUCTORS, 75°C" or Equivalent.
Screw Driver
Width
Screw Size
M2
Screw Torque
2.5 lb·in (0.28 N·m)
4
www.productivity2000.com
P2-RTB-1
18 Spring Clamp Terminals
)
28–16 AWG (0.081–1.31 mm
2
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
1/8 inch (3.8 mm) Maximum
N/A
N/A
General Specifications
Operating Temperature
Storage Temperature
Humidity
Environmental Air
Vibration
Shock
Field to Logic Side Isolation
Insulation Resistance
Heat Dissipation
Enclosure Type
Module Keying to Backplane
Module Location
Field Wiring
EU Directive
Connector Type (not included) 18-position removable terminal block
Weight
Agency Approvals
*Meets EMC and Safety requirements. See the D.O.C. for details.
)
2
0° to 60°C (32° to 140°F)
-20° to 70°C (-4° to 158°F)
5 to 95% (non-condensing)
No corrosive gases permitted
IEC60068-2-6 (Test Fc)
IEC60068-2-27 (Test Ea)
1800VAC applied for 1 second
>10MΩ @ 500VDC
325mW
Open Equipment
Electronic
Any I/O slot in a Productivity2000 System.
Use ZIPLink Wiring System or removable terminal
block (not included). See "Wiring Options" on
page 2.
See the "EU Directive" topic in the
Productivity2000 Help File. Information can also
be obtained at: www.productivity2000.com
90g (3.2 oz)
UL 61010-2-201 file E139594, Canada & USA
CE (EN61131-2 EMC and EN61010-2-201 Safety*)
Tech Support 770-844-4200