AFG 2.0AS Assembly and Manual de montaje y uso - Página 7
Navegue en línea o descargue pdf Manual de montaje y uso para Gimnasio en casa AFG 2.0AS Assembly and. AFG 2.0AS Assembly and 15 páginas. Afg series
También para AFG 2.0AS Assembly and: Manual de montaje y uso (16 páginas)
Imprimir página
AS SE MB LY ST EP ( 2 0 0 lb s. We igh t Sta ck )
HARDWARE BAG CONTENTS :
FLAT WASHER (C)
Qty: 8
A
Open HARDWARE BAG .
UPPER MOUNTING BRACKET
B
Attach LOWER MOUNTING BRACKET (after
FLAT WASHER (I)
removing pre-installed guide rod bolts) to BASE
BOLT (Q)
NYLON NUT (K)
FRAME in desired location, using 2 BOLTS (P), 4
FLAT WASHERS (C) and 2 NYLON NUTS (E).
BOLT (O)
NOTE: Refer to page 25 for mounting positions.
FLAT
WASHER (I)
C
Position each GUIDE ROD so that the mounting
UPPER
holes are in the upper position, and insert
GUIDE
PULLEY
ROD
GUIDE RODS into corresponding sleeves in
ASSEMBLY
LOWER MOUNTING BRACKET.
FLAT
WASHER (C)
BAYONET
D
Slide 1 RUBBER BUMPER onto each guide rod,
WEIGHT
NYLON NUT (E)
PLATES
as shown in diagram.
RUBBER
BUMPER
E
Install each WEIGHT PLATE onto guide rod as
shown in diagram. Ensure than the weight pin
UPGRADE
selector slot is positioned downward and in
SPACER
BOLT (P)
same direction.
F
Install BAYONET onto GUIDE RODS as shown in
diagram.
G
Re-install GUIDE ROD bolts into LOWER
LOWER MOUNTING
MOUNTING BRACKET.
BRACKET
H
Install UPPER MOUNTING BRACKET to top of
FLAT WASHER (C)
GUIDE RODS, as shown in diagram, using 2
BASE FRAME
NYLON NUT (E)
BOLTS (Q), 4 FLAT WASHERS (I), and 2 NYLON
NUTS (K).
I
Attach UPPER MOUNTING BRACKET to UPPER PULLEY ASSEMBLY using 2 BOLTS (O), 4
FLAT WASHERS (C), and 2 NYLON NUTS (E).
NOTE: Ensure that the UPPER MOUNTING BRACKET's position corresponds to the position
of the LOWER MOUNTING BRACKET before securing it to the UPPER PULLEY ASSEMBLY.
j
Tighten all hardware.
12
2.0AS_Rev.1.5.indd 12-13
NYLON
FLAT WASHER (I)
NYLON
NUT (E)
Qty: 4
NUT (K)
Qty: 4
Qty: 2
BOLT (O)
BOLT (P)
100 mm
70 mm
Qty: 2
Qty: 2
UPPER MOUNTING BRACKET
FLAT WASHER (I)
NYLON NUT (K)
BOLT (O)
UPPER
PULLEY
ASSEMBLY
FLAT
WASHER (C)
NYLON NUT (E)
BOLT (P)
LOWER MOUNTING
FLAT WASHER (C)
BASE FRAME
NYLON NUT (E)
ASSEMBLY STEP
HARDWARE BAG CONTENTS :
RUBBER
BUMPER
Qty: 2
BOLT (Q)
40 mm
Qty: 2
DUAL FLOATING
PULLEY BRACKET
SINGLE FLOATING
PULLEY BRACKET
BOLT (Q)
FLAT
WASHER (I)
GUIDE
ROD
BAYONET
WEIGHT
PLATES
RUBBER
BUMPER
CABLE A
BRACKET
WEIGHT SELECTION
PIN TETHER
A
Open HARDWARE BAG .
CABLE A
B
Install SINGLE FLOATING PULLEY
Qty: 1
BRACKET onto one end of CABLE A.
C
Remove THREADED SCREW and NUT
from other end of CABLE A.
D
Route CABLE A through pulleys as
CABLE A
shown in diagram.
CABLE A
NOTE: DUAL FLOATING PULLEY
BRACKET must be installed after
CABLE A is routed through first pulley.
E
After CABLE A routing is complete,
install THREADED SCREW and NUT
onto cable end and thread through
WEIGHT SELECTION PIN tether into
BAYONET.
NOTE: Always maintain at least 1/2"
of CABLE A SCREW threaded into
BAYONET for safety.
BAYONET
BAYONET
1
9/23/08 10:14:44 AM