Dynamis D40 Manual del usuario - Página 9

Navegue en línea o descargue pdf Manual del usuario para Amplificador para instrumentos musicales Dynamis D40. Dynamis D40 11 páginas.

Imprimir página

Dynamis

R E V V |

D 4 0

TORPEDO REMOTE &

REACTIVE LOAD

The amplifier can be connected to Two notes Remote

software to manipulate all available settings and

change the presets found on the front knob of the

amplifier.

This is via the USB port. You can find the

Remote Software for the amplifier here:

https://www.two-notes.com/downloads

Once you connect to the computer using the provided

USB cable, your computer will start recognizing the

amplifier. This may take a couple of minutes. Once

this is complete, simply open the Remote Software

and the amp will connect. Once connected, you can

tweak all available Torpedo Embedded settings to your

preferences!

Note: If you are new to studio practices such as

mic placement, the difference in tonalities between

different speakers and more Two notes has a wealth

of resources available throughout their channels to get

you started. Of course, the presets are the best start in

this situation!

BLUETOOTH CONNECTION

You will connect to the Two Notes Torpedo inside your

Revv Amplifier from your mobile device via Bluetooth.

The connection has to be done in the following order:

1. Launch the Torpedo Wireless Remote app

2. Accept all the requested authorizations

(they depend on your tablet or phone)

3. The connection window should show up and when

it does, follow the on screen instructions.

4. Input the pin code to pair the Torpedo in your Revv amplifier

and your mobile device. The pin code is found with your

amplifier. Contact Revv should you misplace the Pin Code.

TROUBLESHOOTING

If after inputting the pin code the Torpedo does not

show up in the "Devices" menu in Torpedo Wireless

Remote, you will need to unpair the Torpedo in the

list of devices that are paired in the Bluetooth menu

of your phone. Once you have done this, please redo

the procedure detailed above. You cannot pair the

Torpedo from the phone or tablet OS, it has to be done

by Torpedo Wireless Remote. Some phones need to

have the location (GPS) activated to allow for Bluetooth

pairing. Try activating the Location if you find yourself

unable to pair with just the Bluetooth activated on your

phone or tablet.

INTERNAL REACTIVE LOAD

Your amplifier comes with a built-in, fan-cooled,

reactive load to allow you to play without the need for

a speaker cabinet. On the rear of the amplifier, there is

an internal load/speaker switch to switch between the

speaker cabinet and the reactive load.

Depending on what you need, you can switch between

the two on the fly. The speaker cabinet does not have

to be unplugged when switching to the reactive load,

the switch will bypass the speaker cab and only use

the reactive load or vice versa! So you have full control

by simply using the switch..

Note: If you forget to plug in a speaker cab and run

the amplifier without a speaker cab fear not! The

amplifier automatically uses the reactive load if there

is no speaker plugged into the amplifier. But be aware,

if there is a cable plugged into the speaker jack on the

amplifier but no speaker cab plugged into the other end

of the cable, this will cause damage unless the reactive

load is engaged by using the internal load switch!

SETTINGS &

SAVING CABINETS

The amplifier by default will power up with channel

1 loaded and all options turned off. But if you would

prefer to save how the amplifier powers up and how

each channel is set at power up you can!

Any combination of channels, boost settings and

functions can be saved so that the amplifier will always

power up in your favorite setting. In order to perform

this setting:

In order to perform this setting:

1. Select the channel you want to power

up with and set it up to your preference.

2. Press the store button and quickly release.

3. The store led will now flash

4. Press the CH button of the channel you have active.

The amplifier will now store your setting and confirm

it by flashing the store led quickly and turn off. That's

it! Your favorite setting will now be loaded when the

amplifier is powered up. This will remain until changed.

Note: Each channel can be set up this way, however,

the last channel saved will be the first channel to

become active when the power is turned on. So when

setting your channels up the way you want them when

power is applied, just remember that you want to save

your power up channel last.

FRONT PANEL & CAB LIGHTING

While we know a lot of people like the color-changing

Revv logo and cabinet lighting, some do not. The

option to turn this feature on and off has been added

to your amplifier!

To disable/enable the cab and logo lighting:

With the main power in the OFF position

R E V V |

1. Press & hold the Reverb and Store push buttons

together.

2. With the push buttons being held, turn on the

power switch.

3. If the buttons were held correctly, then the CH1,

Ch2, Boost and Bright buttons will illuminate.

The logo LED'S will either now be on or off for

complete amplifier customization!

4. Release the Reverb and Store buttons once the

CH1, CH2, Boost and Bright Buttons Illuminate.

5. Press the BOOST button to toggle the Front Panel

and Cab lighting LEDs.

The amplifier will now restart, and the LEDs will be

turned off. Now, every time you power on the amplifier,

the lighting will be turned off.

SAVING GLOBAL/MASTERS

While the FX Loop and Master functions are considered

global settings across all channels, some players

might prefer that these functions are saved differently

on each channel. In this case, the amplifier has been

designed to offer either setting so that it is possible to

have each channel call up a different setting for both

the FX loop as well as the master volumes.

This can be a pretty powerful feature if your settings

will always remain the same.

By default, these functions are set to global as most

players will require the FX Loop and master to remain

the same across all channels (global).

But to toggle the amp to store these settings differently

among the channels, simply turn on the saved FX Loop/

Masters setting.

Dynamis

D 4 0