Dynamite Passport Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Cargador de batería Dynamite Passport. Dynamite Passport 2 páginas. Duo 400w dual ac/dc touch charger

Imprimir página

6 - NICkEl DISChArgINg

1. Connect the battery connector to the device connector.

9. Press the arrow in the top right of the LCD Touch screen to see the rest of

the Discharging information.

2. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.

NiMH DCHG

Program select=NiMH

End Volt

Int Temp

Safety Timer

Capacity Limit :

N i M H

STOP

CHG

DCHG

CYCLE

10. Press Graph to see the battery voltage graph. Press back to return to the

3. Press DChG.

discharging screen.

NiMH DISCHARGE

End Volt

0.10V

Data NiMH = Graph

Capacity

50mAh

Current

0.1A

Press&Hold

DISCHRG

BACK

SELECT

8.39V

000:47S

4. Press a parameter to highlight that parameter.

11. Press sTOP at any time to stop discharging.

5. Press the Up and Down Arrows to edit the parameter.

12. When discharging is complete, the charger will sound a series of beeps and

6. Press select to save the parameter.

display the following screen:

7. Once the parameters are at the desired settings, press and hold DIsChRG.

NiMH DONE

8. The charger will check the battery and charger settings and discharging will begin. The

Capacity

charger will beep and display the following screen:

Current

Voltage

Resistance

NiMH DCHG

000:34S

Peak Temp.

Capacity

16mAh

BACK

Cycle

Current

1.8A

Voltage

8.43V

Resistance

****mΩ

13. Press the arrow in the top right of the LCD Touch screen to see the rest of

Peak Temp.

No sens

the Charging information.

STOP

Graph

NiMH DONE

End Volt

Int Temp

Safety Timer

Capacity Limit :

STOP

14. Disconnect the battery from the charger.

7 - NICkEl CYClE ChArgINg

Connect the battery connector to the device connector.

11. Press CYCLE to see the voltage and amperage applied to each cycle.

Press the Left and Right Arrows on the LCD Touch screen to scroll

Data NiMH = Cycle 1/1

through the main menu screens until you reach Program Select=Ni-MH/

Ni-Cd.

--CHG--

00.00Vp

Program select=NiMH

00000mAh

Back

N i M H

12. Press Graph to see the battery voltage graph. Press back to return to the

charging screen.

CHG

DCHG

CYCLE

Data NiMH = Graph

3. Press CYCLE.

NiMH CYCLE

[1/2]

Capacity

3300mAh

CHG Curr.

3.3A

DCHG Curr.

0.1A

DCHG End Volt

0.10V

8.03V

000:28S

Press&Hold

CYCLE

13. Press sTOP at any time to stop charging.

BACK

SELECT

14. When cycle charging is complete, the charger will sound a series of beeps and

4. Press a parameter to highlight that parameter.

display the following screen:

5. Press the Up and Down Arrows to edit the parameter.

NiMH DONE

6. Press select to save the parameter.

Capacity

7. Press the top right of the LCD Touch screen to get to the next set of

Current

Voltage

parameters.

Resistance

8. Once the parameters are at the desired settings, press and hold CYCLE.

Peak Temp.

9. The charger will check the battery and charger settings and cycle charging will

BACK

Cycle

begin. The charger will beep and display the following screen:

NiMH CYCLE

000:06S

15. Press the arrow in the top right of the LCD Touch screen to see the rest of

Capacity

4mAh

the Charging information.

Current

3.3A

Voltage

7.97V

Resistance

53mΩ

Peak Temp.

No sens

NiMH DONE

STOP

CYCLE

Graph

Input Volt

Delta Peak

Int Temp.

10. Press the arrow in the top right of the LCD Touch screen to see the rest of

Safety Timer

the Cycle information.

Capacity Lim. :

NiMH DONE

001:15S

BACK

Cycle

Input Volt

14.8?V

Delta Peak

8mV/C

Int Temp.

60F

16. Disconnect the battery from the charger.

Safety Timer

240min

Capacity Lim. :

3300mAh

BACK

Cycle

Graph

CAUTION: The Pb charge program menus are to be used ONLY for the charging and discharging of Pb battery packs. Charging other battery types using the Pb

charge programs will damage the battery or the charger.

8 - PB ChArgINg

1. Connect the battery connector to the battery adapter cable.

9. Press sTART. The charger will beep and display the following screen:

2. Press the Left and Right Arrows on the LCD Touch screen to scroll through

Pb CHG

the main menu screens until you reach Program Select=Pb.

Capacity

Current

Program select=Pb

Voltage

Resistance

Peak Temp.

STOP

CHG

DCHG

10. Press the arrow in the top right of the LCD Touch screen to see the rest of

the charging info.

3. Press ChG.

11. Press Graph to see the battery voltage graph. Press back to return to the

charging screen.

Pb CHARGE

Pack. Volt.

2V/1P

Data Pb

= Graph

Capacity

50mAh

Current

0.1A

Press&Hold

CHARGE

BACK

SELECT

14.68V

000:12S

4. Press a parameter to highlight that parameter.

12. Press sTOP at any time to stop charging.

5. Press the Up and Down Arrows to edit the parameter.

13. When charging is complete, the charger will sound a series of beeps and

6. Press select to save the parameter.

display the following screen:

7. Once the parameters are at the desired settings, press and hold ChARGE.

8. The charger will check the battery and charger settings and display the

Pb DONE

Capacity

following screen:

Current

Pb Charge Confirm

Voltage

Resistance

Peak Temp.

-Connect-

-Check-

BACK

Input • • • • OK

Set: 6P

BATT. • • • • OK

Read: 5P

14. Disconnect the battery from the charger.

Back

START

9 - PB DISChArgINg

Connect the battery connector to the battery adapter cable.

9. Press sTART. The charger will beep and display the following screen:

Press the Left and Right Arrows on the LCD Touch screen to scroll

through the main menu screens until you reach Program Select=Pb.

Program select=Pb

000:09S

12.24V

21ºC

240min

2100mAh

CHG

DCHG

10. Press the arrow in the top right of the LCD Touch screen to see the rest of

Graph

the discharging information.

3. Press DChG.

11. Press Graph to see the battery voltage graph. Press back to return to the

Discharging screen.

Pb DISCHARGE

Pack. Volt.

2V/1P

Capacity

50mAh

Current

0.1A

BACK

Press&Hold

DISCHRG

BACK

SELECT

4. Press a parameter to highlight that parameter.

12. Press sTOP at any time to stop discharging.

5. Press the Up and Down Arrows to edit the parameter.

13. When discharging is complete, the charger will sound a series of beeps and

6. Press select to save the parameter.

display the following screen:

7. Once the parameters are at the desired settings, press and hold DIsChRG.

8. The charger will check the battery and charger settings and display the

following screen:

001:15S

53mAh

Pb DCHG Confirm

0.0A

8.16V

53mΩ

-Connect-

-Check-

No sens

Input • • • • OK

Set: 6P

BATT. • • • • OK

Read: 5P

Graph

14. Press the arrow in the top right of the LCD Touch screen to see the rest of

BACK

START

the Charging information.

15. Disconnect the battery from the charger.

000:09S

12.24V

21ºC

240min

2100mAh

Graph

10 - SETuP

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

Parameters

the main menu screens until you reach Program Select=Setup.

Program select=Setup

--DISCHG--

00.00Va

Input Power Low Voltage Cutoff 10.0V–17.5V

00000mAh

Down

SETUP

2. Press sETUP.

USER SETUP

[1/4]

BACK

Temp (ºC/ºF)

ºC

Temp Cutt-Off :

60ºC

Input Low Volt :

10.0V

Input Limited :

Auto

DCHG Mode

BACK

SELECT

3. Press a parameter to highlight that parameter.

4. Press the Up and Down Arrows to edit the parameter.

5. Press select to save the parameter.

6. Press the top right of the LCD Touch screen to get to the next set of

001:15S

parameters.

53mAh

0.0A

8.16V

USER SETUP

[2/4]

53mΩ

Balance Volt

Auto

No sens

Balance Force :

Auto

Full Force

Auto

Graph

MH/Cd Trickle :

OFF

Safety Timer

240min

BACK

SELECT

USER SETUP

[3/4]

Back Light

100%

001:15S

Melody

14.8?V

Button Sound

8mV/C

Buzzer Sound

60F

Buzzer Vol

100%

240min

3300mAh

BACK

SELECT

Graph

USER SETUP

[4/4]

ENTER_USER_NAME

Version#

1.00

Press&Hold

-≥

FCTY_RST

BACK

SELECT

11 - VIEW

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

3. Press CELLs to view the connected lithium battery's individual cell voltage.

the main menu screens until you reach Program Select=View.

Program select=View

000:16S

8mAh

1.7A

14.69V

VIEW

BALANCE

****mΩ

No sens

2. Press VIEW. The screen will display the current charger status.

Graph

DATA VIEW

Input Volt

15.30V

Output Volt

0.02V

Int Temp.

29ºC

Ext Temp.

No sens

Resistance

****mΩ

BACK

CELLS

BACK

12 - BAlANCE

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

5. Press sTOP at any time to stop balancing.

the main menu screens until you reach Program Select=View.

6. When balancing is complete, the charger will beep and display the following

screen:

Program select=View

000:19S

VIEW

BALANCE

8mAh

1.7A

11.60V

2. Press bALANCE.

****mΩ

3. Press the type of battery you want to balance: Li-Po/Li-Ion/Li-Fe.

No sens

4. Press sTART. The charger will begin balancing the cells.

Graph

BATTERY

LiPo

LiIon

LiFE

BACK

START

Created 06/2016 | 48546

13 - MEMOrY

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens until you reach the battery program you would like to

Pb DCHG

000:19S

save: Program Select=Li-Po/Li-Fe/Li-Ion/Ni-MH/Ni-Cd/Pb.

Capacity

8mAh

Current

1.7A

2. Press the action at the bottom of the LCD Touch screen to enter that menu.

Voltage

11.60V

3. Press a parameter to highlight that parameter.

Resistance

****mΩ

4. Press the Up and Down Arrows to edit the parameter.

Peak Temp.

No sens

STOP

Graph

5. Press select to save the parameter.

6. If there is more than one screen of parameters, press the top right corner of

the LCD Touch screen to scroll through the parameter screens.

7. Once the parameters are at the desired settings, press back to return to the

main menu screens.

8. Press the Left and Right Arrows on the LCD Touch screen to scroll through

Data Pb

= Graph

the main menu screens until you reach Program Select=Memory.

BACK

Program select=Memory

11.54V

000:32S

MEMORY

9. Press MEMORY.

Pb DONE

000:19S

Capacity

8mAh

Current

1.7A

Voltage

11.60V

Resistance

****mΩ

Peak Temp.

No sens

BACK

Graph

14 - uSB DEVICE ChArgINg

The charger has the capability to charge any USB-compatible device with the 2.1A Usb Power Output Port (F). To use the charging function, simply connect a

compatible charging device or cord into the charge port while the charger is powered ON. The charger provides up to 2.1A current at 5V DC.

15 - TrOuBlEShOOTINg

During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger's LCD screen, make the recommended

responses. If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance.

REVERSE POLARITY

Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery.

PROCESS INTERRUPTED

Make sure the power connections are correct for charging.

OUTPUT SHORT CIRCUIT

Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires.

INPUT VOLTAGE ERROR

Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger

provides correct input voltage.

Temperature °C/°F

CHARGER FAILURE

Charger electronics require repair.

Temperature Cutoff 68–176°F (20–80°C)

BATTERY LOW VOLTAGE

Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the

battery.

Input LImited 1.0–16,5A

BATTERY HIGH VOLTAGE

Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the

battery.

DChG Mode CC–CV

Balance Voltage 0.01V–0.03V

CELL LOW VOLTAGE

Cell voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the

battery.

Balance Force -0.01–7.00V

CELL HIGH VOLTAGE

Cell voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the

MH/Cd Trickle 50mA–200mA

battery.

Safety Timer 1–255 minutes

CELL CONNECT ERROR

Make sure the balance connection is correct for charging.

back Light OFF–100%

CHARGER OVERHEATING

Charger temperature is too high. Power OFF the charger and let it cool.

Melody 1–5

OVER POWER

Input voltage to the charger exceeded the default or adjusted input voltage setting. Make sure the power source for the charger provides

Button Sound ON/OFF

the correct input voltage.

Buzzer Sound ON/OFF

MAX CURRENT

Current is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery.

Buzzer Volume 0–100%

SAFETY TIMER

Maximum safe time limit has been reached.

Username Enter your name here

MAX CAPACITY

Maximum capacity limit has been reached.

Version 1.0

MAX EXT. TEMP

External temperature is too high. Let charger and battery cool.

Press and hold FCTY RST to return the

Factory Reset

charger to default factory settings.

DYNAMITE 5-YEAr uS lIMITED ChArgEr WArrANTY INfOrMATION

Horizon Hobby is so confident about the quality of our Dynamite chargers we offer a 5-year replacement plan on all of our Dynamite

5-year replacement plan requires proof of purchase (copy of the receipt), and we do reserve the right to deny replacement to any abusers of our plan. See below for full

details. Contact the appropriate Horizon Service Department for instructions on warranty claims.

5-YEAr uS lIMITED WArrANTY

Warranty Period - Exclusive Warranty - Horizon Hobby, LLC., ("Horizon") warrants

that the included Dynamite Prophet, or Passport charger ("Product") will be free from

defects in materials and workmanship for a period of five (5) years after the date of

purchase ("Warranty Period").

What is Not Covered - This warranty is not transferable and does not cover

(i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse,

negligence, commercial use, or due to improper use, installation, operation

or maintenance, (iii) modification of or to any part of the Product, (iv) attempted

service by anyone other than a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, (vi) Product not compliant with

applicable technical regulations, or (vii) use that violates any applicable laws, rules,

or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE

HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS

OF THE PURCHASER'S INTENDED USE.

Horizon's sole obligation and purchaser's sole and exclusive remedy shall be that

DATA View–CELLS

Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by

BACK RES.

Horizon to be defective. Horizon reserves the right to inspect any and all Product(s)

involved in a warranty claim. Service or replacement decisions are at the sole

discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE

OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER'S

SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

0.00 0.00 0.00 0.00 0.00 0.00

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION

OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM

IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR

ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon

exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, final assembly, modification or misuse, no liability

shall be assumed nor accepted for any resulting damage or injury. By the act of use,

setup or assembly, the user accepts all resulting liability. If you as the purchaser or

user are not prepared to accept the liability associated with the use of the Product,

purchaser is advised to return the Product immediately in new and unused condition

to the place of purchase.

Law - These terms are governed by Illinois law (without regard to conflict of law

principals). This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state. Horizon reserves the right to change or

modify this warranty at any time without notice.

WARRANTY sERVICEs

Questions, Assistance, and Services - Your local hobby store and/or place of

–Balancing Complete–

purchase cannot provide warranty support or service. Once assembly, setup or use

BACK RES.

of the Product has been started, you must contact your local distributor or Horizon

directly. This will enable Horizon to better answer your questions and service you in

the event that you may need any assistance. For questions or assistance, please visit

our website at www.horizonhobby.com, submit a Product Support Inquiry at https://

horizonhobby.quickbase.com/db/bghj7ey8c?a=GenNewRecord, or call the toll free

3.94 3.94

0.00 0.00 0.00 0.00

telephone number referenced in the Warranty and Service Contact Information

section to speak with a Product Support representative.

NON-uS lIMITED WArrANTY

What this Warranty Covers - Horizon Hobby, LLC ("Horizon") warrants to the

10. Choose an empty memory profile and press it.

original purchaser that the product purchased (the "Product") will be free from

defects in materials and workmanship at the date of purchase.

USER SETUP

[1/4]

M01 NULL

What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic

M02 NULL

damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence,

M03 NULL

commercial use, or due to improper use, installation, operation or maintenance, (iii)

M04 NULL

modification of or to any part of the Product, (iv) attempted service by anyone other

M05 NULL

than a Horizon Hobby authorized service center, (v) Product not purchased from an

BACK

DEL

LOAD

SAVE

authorized Horizon dealer, or (vi) Product not compliant with applicable technical

regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

11. Press sAVE. The charging parameters you just entered will be saved in that

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL

memory profile.

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

12. To use a memory profile, press it, then press LOAD.

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR

13. To delete a memory profile, press it, then hold DEL.

A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE

HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS

14. Press the top right of the LCD Touch screen to scroll through all 20 memory

OF THE PURCHASER'S INTENDED USE.

profiles.

Purchaser's Remedy - Horizon's sole obligation and purchaser's sole and exclusive

remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any

Product determined by Horizon to be defective. Horizon reserves the right to inspect

any and all Product(s) involved in a warranty claim. Service or replacement decisions

are at the sole discretion of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

PURCHASER'S SOLE AND EXCLUSIVE REMEDY.