Dynamite Prophet DYNC2040 Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Cargador de batería Dynamite Prophet DYNC2040. Dynamite Prophet DYNC2040 8 páginas. Sport quad 4x50w ac/dc battery charger

Imprimir página

Prophet

Sport Quad 4x50W AC/DC Battery Charger

™

Instruction Manual | Bedienungsanleitung | Manuel d'utilisation | Manuale di Istruzioni

NOTIcE

All instructions, warranties and other collateral documents are subject to change at the sole

discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and

click on the support tab for this product.

MEANING OF SPEcIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of

potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property

damage AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property

damage AND possibility of serious injury.

WArNINg: Procedures, which if not properly followed, create the probability of property

damage, collateral damage, and serious injury OR create a high probability of superficial injury.

WArNINg: Read the ENTIRE instruction manual to become familiar with the features of

the product before operating. Failure to operate the product correctly can result in

damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and

requires some basic mechanical ability. Failure to operate this Product in a safe and responsible

manner could result in injury or damage to the product or other property. This product is not

intended for use by children without direct adult supervision. Do not attempt disassembly, use

with incompatible components or augment product in any way without the approval of Horizon

Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is

essential to read and follow all the instructions and warnings in the manual, prior to assembly,

setup or use, in order to operate correctly and avoid damage or serious injury.

Age recommendation: Not for children under 14 years. This is not a toy.

NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

DANgEr: To reduce the risk of fire or electric shock, carefully follow these instructions.

VOLTAGE SELEcTOr (E) MUST BE SET TO ThE cOrrEcT VALUE BEFOrE ThE chArGEr IS POWErED ON.

CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can

cause fire, collateral damage and injuries.

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types using the Lithium charge

programs will damage the battery or the charger.

PrOGrAMMING qUIck GUIDE

1. Press the Esc / Mode Button to scroll through the main menu screens.

2. Press Start / Enter.

3. Press the Dec or Inc Button to scroll through the program options.

4. Press Start / Enter to select a program option.

LITHIUM BATTErIEs (Li-Po / Li-Fe / Li-Ion)

PROGRAM SELECT

Li** Battery

Ni-MH BATTErIEs

PROGRAM SELECT

NiMH Battery

Ni-Cd BATTErIEs

PROGRAM SELECT

NiCd Battery

Pb BATTErIEs

PROGRAM SELECT

Pb Battery

DIGITAL POWEr

PROGRAM SELECT

Digital Power

sAVE DATA

PROGRAM SELECT

Memory Save

LOAD DATA

PROGRAM SELECT

Memory Load

Values in screens are for example only

chArGING WArNINGS

WArNINg: Failure to exercise caution while using this product and comply with the

following warnings could result in product malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

• NEVEr LEAVE ChArgINg BATTErIES UNATTENDED DUrINg USE.

• NEVEr ChArgE BATTErIES OVErNIghT.

• Never attempt to charge dead, damaged or wet battery packs.

• Never attempt to charge a battery pack containing different types of batteries.

• Never allow children under 14 years of age to charge battery packs.

• Never charge batteries in extremely hot or cold places or place in direct sunlight.

• Never charge a battery if the cable has been pinched or shorted.

• Never connect the charger if the power cable has been pinched or shorted.

• Never connect the charger to an automobile 12V battery while the vehicle is running.

• Never attempt to dismantle the charger or use a damaged charger.

• Never attach your charger to both an AC and a DC power source at the same time.

• Never connect the input jack (DC input) to AC power.

• Always use only rechargeable batteries designed for use with this type of charger in the correct

programming mode.

• Always inspect the battery before charging.

• Always keep the battery away from any material that could be affected by heat.

• Always monitor the charging area and have a fire extinguisher available at all times.

• Always end the charging process if the battery becomes hot to the touch or starts to change

form (swell) during the charge process.

• Always connect the charge cable to the charger first, then connect the battery to avoid short

circuit between the charge leads. Reverse the sequence when disconnecting.

• Always connect the positive red leads (+) and negative black leads (–) correctly.

• Always disconnect the battery after charging, and let the charger cool between charges.

• Always charge in a well-ventilated area.

• Always terminate all processes and contact Horizon Hobby if the product malfunctions.

• Charge only rechargeable batteries. Charging non-rechargeable batteries may cause the

batteries to burst, resulting in injury to persons and/or damage to property.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

WArNINg: Never leave charger unattended, exceed maximum charge rate, charge with

non-approved batteries or charge batteries in the wrong mode. Failure to comply may

result in excessive heat, fire and serious injury.

CAUTION: Always ensure the battery you are charging meets the specifications of this

charger and that the charger settings are correct. Not doing so can result in excessive

heat and other related product malfunctions, which can lead to user injury or property damage.

Please contact Horizon Hobby or an authorized retailer with compatibility questions.

5. Press the Dec or Inc Button to change the parameter. Press the Start / Enter Button

again to move to the next parameter.

6. Once the parameters are at the desired settings, press and hold the Start / Enter

Button for 3 seconds.

7. Press the Esc / Mode Button at any time to stop charging.

Li** CHARGE

C= 5000mAh

5.0A

Li** BAL-CHG

C= 5000mAh

5.0A

Li** STORAGE

C= 5000mAh

5.0A

Li** DCHG

3.0

1.0A

18.0V(6S)

NiMH CHARGE Man

CURRENT

1.0A

NiMH CHARGE

Aut

CUR LIMIT

1.0A

NiMH DISCHARGE

1.0A

12.0V

C=1.0A D=1.0A

NiCd CHARGE Man

CURRENT

1.0A

NiCd CHARGE

Aut

CUR LIMIT

1.0A

NiCd DISCHARGE

1.0A

12.0V

C=1.0A D=1.0A

Pb CHARGE

0.1A

4.9V (2P)

Pb DISCHARGE

1.0A

4.9V (2P)

POWER MODE

2.0A

12.0V

MEMORY NiMH

[1]

AUTO

1.5A

MEMORY NiMH

[1]

AUTO

1.5A

Included Items

DC Power Cord (DYNC1106)

Charge Adapter: Banana to EC3 Device (2) (DYNC0072)

Charge Adapter: Banana to deans Compatible Male (2) (DYNC0056)

Banana to RX (DYNC0033)

Balancing Adapter Board :XH (2) (DYN5032)

Balancing Adapter Board: TP/FP (DYNC0101)

Optional Items

Banana to Deans insulated charge adapter: male (DYNC0053)

Banana to Traxxas

insulated charge adapter: male (DYNC0054)

Temperature Sensor (DYN5033)

Dynamite

LiPo Charge Bag: small (DYN1400), large (DYN1405)

Specifications

Input Voltage 100–240V AC (50–60Hz); 11–18V DC

Charging Capability 1–6S Li-Po/Li-Ion/Li-Fe;

1–15C Ni-Cd/Ni-MH; 2–24V Pb

Battery Capacities 50–10000 mAh

Charge Current 0.1A–6A x 4 (in 0.1A increments/50W max)

Discharge Current 0.10A–2.0A x 4 (in 0.1A increments/10W max)

Balance Current 300mA max

Balance tolerance +/- 0.01V

Operating Temperature 0ºC to + 40ºC

Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV

Protection Short-circuit, over-current, reverse polarity, low input voltage,

over-temperature

Digital Power 6A/24V max

Not to scale.

Not all wiring shown.

Not all connectors shown.

OPErATING YOUr chArGEr

1 - SELF TEST AND PrOgrAM SELECT SCrEENS

When the charger is powered ON, there is a series of self tests and the screen will show the

charger brand name and model number.

DYNAMITE

DYNC2040

ONLy LI-PO IS ShOWN IN ThE FOLLOWINg ThrEE SECTIONS. LI-ION/LI-FE

MENUS DIFFEr ONLy IN CELL AND PACK VOLTAgE VALUES.

2 - LIThIUM (LI-PO/LI-FE/LI-ION) ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. If Balance Charging, connect the JST_XH balance adapter to the Balance Circuit Adapter

Board Connector of the selected charge port (D,h).

3. Connect the battery connector to the battery adapter cable.

4. If Balance Charging, connect the balance connector of the battery to the JST_XH balance

adapter.

5. Press the Esc / Mode Button to scroll through the main menu screens until you reach

Program Select=Li-Po/Li-Ion/Li-Fe.

PROGRAM SELECT

Li** Battery

6. Press Start / Enter.

7. Press the Esc / Mode Button at any time to stop charging.

8. Press the Dec or Inc Button to scroll through the program options (Charge, Balance Charge,

Storage, Discharge).

Li** BAL-CHG 3S

C= 2200mAh

2.2A

9. Press Start / Enter to select a program option.

10. Press the Dec or Inc Button to change the parameter. Press the Start / Enter Button again to

move to the next parameter.

11. Once the parameters are at the desired settings, press and hold the Start / Enter Button for

3 seconds.

12. The charger will check the battery and charger settings and charging will begin. The charger

will beep and display the following screen:

Li** BAL-CHG 3S

C= 3200mAh

3.2A

13. Press the Dec Button to see the rest of the Charging information.

14. Press the Inc Button to see the voltages for each cell. Press Dec to return to the charging

screen.

4.20 4.20 4.20

0.00 0.00 0.00

15. When charging is complete, the charger will sound a series of beeps.

16. Disconnect the battery from the charge adapter.

GETTING STArTED

CAUTION: Before charging, always ensure you have chosen the correct battery chemistry

type for the battery you are charging.

CAUTION: Never connect the AC and DC input cords to an active power source at the same

time. This will void the warranty, cause product damage and possibly injure the user.

When Using an External DC Power Source:

1. Connect the DC power cord to the charger DC Power Input Port (B).

2. Connect the DC alligator clips to the DC power source.

3. When the charger is powered ON, a message will appear on the LCD Screen (I,J,O,P).

NOTICE: Always connect cable polarities correctly.

NOTICE: Always consult 12V battery collateral materials or Horizon Hobby before using with

sources other than a standard AC wall outlet.

WhEN Using an External AC Power Source:

1. Connect the AC power cord to the charger AC Power Input Port.

2. Connect the AC power cord to the AC power source.

3. When the charger is powered ON, a message will appear on the LCD Screen (I,J,O,P).

CONNECTINg BATTErIES TO ThE ChArgEr:

CAUTION: Always power ON the charger before connecting a battery, or damage to the

charger and the battery can result.

1. Connect the charger to the power source.

2. Select charge port (1,2,3,4).

3. Select the charging settings.

4. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (1,2,3,4), making sure that the positive and negative connectors are not reversed.

5. Connect the battery connector to the battery adapter cable.

6. Start battery charging.

A. Power Output Ports (2,4)

I. Charger 1 LCD Screen

B. DC Power Input Port

J. Charger 3 LCD Screen

C. Temperature Sensor Ports (2,4)

K. Mode / ESC

D. Balance Circuit Adapter Board

L. Decrease

Connectors (2,4)

M. Increase

E. Voltage Selector

N. START / ENTER

F. Power Output Ports (1,3)

O. Charger 2 LCD Screen

g. Temperature Sensor Ports (1,3)

P. Charger 4 LCD Screen

h. Balance Circuit Adapter Board

Connectors (1,3)

3 - LIThIUM DISChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector of

the selected charge port (D,h).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the JST_XH balance adapter.

5. Press the Esc / Mode button to scroll through the main menu screens until you reach Program

Select=Li-Po/Li-Ion/Li-Fe.

6. Press the Start / Enter Button.

7. the Dec or Inc Button until Li-Po/Li-Ion/Li-Fe DCHG appears.

Li** DCHG

3.0V

1.0A

9.0V(3S)

8. Press the Start / Enter Button to edit the parameter.

9. Once the parameters are at the desired settings, press and hold the Start / Enter Button for

3 seconds.

10. The charger will check the battery and charger settings and discharging will begin.

11. Press the Dec or Inc Button to see the rest of the Discharging information.

12. Press Esc / Mode at any time to stop discharging.

13. When discharging is complete, the charger will sound a series of beeps.

14. Disconnect the battery from the charge adapter.

4 - LIThIUM STOrAgE ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output of the selected

charge port (A, F), making sure that the positive and negative connectors are not reversed.

2. Connect the JST_XH balance adapter to the Balance Circuit Adapter Board Connector of

the selected charge port (D,h).

3. Connect the battery connector to the battery adapter cable.

4. Connect the balance connector of the battery to the JST_XH balance adapter.

5. Press the Esc / Mode Button to scroll through the main menu screens until you reach

Program Select=Li-Po/Li-Ion/Li-Fe.

6. Press the Start / Enter Button.

7. The Dec or Inc Button until Li-Po/Li-Ion/Li-Fe STORAGE appears.

LiPo STORAGE 3S

C= 3200mAh

8. Press the Start / Enter Button to edit the parameter.

9. Once the parameters are at the desired settings, press and hold the Start / Enter Button for

3 seconds.

10. The charger will check the battery and charger settings and storage charging will begin.

11. Press the Dec or Inc Button to see the rest of the storage Charging information.

12. Press Esc / Mode at any time to stop charging.

13. When charging is complete, the charger will sound a series of beeps.

14. Disconnect the battery from the charge adapter.

DYNc2040

2.0A