Hifonics BRUTUS BRX640.4 Manual del usuario - Página 3
Navegue en línea o descargue pdf Manual del usuario para Amplificador Hifonics BRUTUS BRX640.4. Hifonics BRUTUS BRX640.4 13 páginas.
Imprimir página
AMPLIFIER FEATURE DESCRIPTIONS
BRUTUS BRX AMPLIFIERS:
Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the
mono amps which are capable of 4, 2 and 1-Ohm loads.
Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers.
The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel amplifiers
and 0.2V to 9V for the mono models.
All crossovers are fully variable in their respective ranges.
Crossover filters are 12dB/Octave.
1 set for channels 1 & 2.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying
daisy chaining of amplifiers.
-HPF: Selects the built in HI PASS filter.
-FULL: Bypasses all crossovers for full frequency range operation.
-LPF: Selects the built in LOW PASS filter.
MODE: Selectable Stereo or MONO operation.
HPF: Variable low frequency cut off from 60Hz to 1.3kHz.
LPF: Variable high frequency cut off from 30Hz to 250Hz.
BASS EQ: 45Hz bass boost variable from 0dB to 12dB.
LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain
multiple amplifiers from one signal.
The 4 channel amps have the same features as the 2 channel models except that there are 2 sets of
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a Mode switch which allows you to select 2 or 4 channel operation.
Switch to 2 channel if you only have 1 set of RCA's in CH 1/2 and the unit will automatically
supply signal to channels 3/4. Select 4 channel if you are providing RCA's to channels 1/2 and 3/4.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying
daisy chaining of amplifiers.
HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.
LOW PASS: Variable high frequency cut off from 30Hz to 150Hz.
BASS EQ: 45Hz bass boost variable from 0dB to 10dB.
LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.
The 5 channel amps have the same features as the 4 channel models except that there are 3 sets of
controls.
1 set for channels 1 & 2, 1 set for channels 3 & 4 and 1 set for channel 5.
In addition, the 4 channel models have a Mode switch which allows you to select 2, 4 or 5 channel operation.
Switch to 2 channel if you only have 1 set of RCA's in CH 1/2 and the unit will automatically
supply signal to channels 2/4/5. Select 4 channel if you are providing RCA's to channels 1/2 and 3/4 and
signal will be internally routed to Ch5. Select 5 if you are supplying RCA's to each INPUT.
The X-OVER slide switch selects the internal crossover functions:
-The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying
daisy chaining of amplifiers.
HI PASS: Variable low frequency cut off from 10Hz to 1.5kHz.
LOW PASS: Variable high frequency cut off from 30Hz to 150Hz. (CH3/4 & 5)
BASS EQ: 45Hz bass boost variable from 0dB to 10dB.
LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V.
REMOTE: This is a remote input jack for the remote level control on Ch5.
SUBSONIC: Crossover filter from 15Hz to 35Hz.
LOW PASS: Crossover filter from 35Hz to 250Hz.
LEVEL: Adjusts the input sensitivity from 0.2 volts to 9 volts.
BASS EQ: Adjustable bass boost from 0db to 10dB.
PHASE:
The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time
alignment.
REMOTE: This is the input jack for the remote Level control.
BALANCED INPUT:
Accepts line level balanced input from 0.4v to 18v.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain
multiple amplifiers from one signal.
-The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the settings on the
amplifier simplifying daisy chaining of amplifiers.
The BRX2400.1D is identical to the other BRX mono amplifiers except that the BRX2400.1D is a
linkable amplifier and features a MASTER / SLAVE selection switch and IN / OUT RCA connection. This
allows for a pair of amps to link at 2-Ohms and produce 4800 watts rms.
A POWER LED indicates the powered up and turned on condition.
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and
amplifier DC faults indicated by the red "PROTECT" LED.
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU WILL
CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE WARRANTY
PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4 and 2-Ohms wired
stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2 and 1-Ohm.
BRX160.2 2-CHANNEL AMPLIFIERS
LINE OUT LINE INPUT
LEVEL
BASS EQ
L
L
FULL LPF HPF
6V
0.2V
0dB
12dB
R
R
Note that the LOW PASS signal is MONO.
-In the LPF position, the HPF filter acts as a subsonic filter.
-When the LPF mode is selected, a 0 to +12dB, at 45Hz, BASS EQ is also switched in.
BRX320.4 / BRX640.4 / BRX1200.4 4-CHANNEL AMPLIFIERS
CH1/2
CH3/4
REMOTE
HI PASS CH1/2 X-OVER LOW PASS BASS EQ
R
R
HI
FULL LP/BP
10Hz 1.5kHz
L
L
2CH
4CH
HI
FULL LP/BP
10Hz 1.5kHz
LINE INPUT
MODE
HI PASS CH3/4 X-OVER LOW PASS BASS EQ
Note that the LOW PASS signal is MONO.
-In the LP/BP position, the HI PASS filter acts as a subsonic filter.
-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz, BASS EQ is also switched
in.
BRX5000.5 5-CHANNEL AMPLIFIERS
LINE INPUT CH1/2 X-OVER HI PASS
LEVEL
HI
FULL
Ch2
Ch4
10Hz 1.5kHz 6V
0.2V 10Hz 1.5kHz
30Hz 150Hz 0dB 10dB 6V
Ch1
Ch3
REMOTE LOW PASS BASS EQ
Note that the LOW PASS signal is MONO.
-In the LP position, the HI PASS filter on Ch3/4 acts as a subsonic filter.
BRX1100.1D / BRX1600.1D / BRX2000.1D MONO BLOCK AMPLIFIERS
BALANCED
INPUT
OUTPUT
INPUT
LEVEL
PHASE
L
L
9V
0.2V
0
R
R
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to the amp not covered in the
warranty.
BRX2400.1D MONO BLOCK AMPLIFIERS
BALANCED
INPUT
OUTPUT
INPUT
LEVEL
PHASE
REMOTE BASS EQ
L
L
9V
0.2V
0
180
R
R
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to the amp not covered in the
warranty.
X-OVER
HPF
LPF
MODE
POWER
MONO
STEREO
60Hz 1.3kHz 30Hz 250Hz
PROTECT
LEVEL
POWER LINE OUTPUT
R
30Hz 150Hz 0dB 10dB 6.0V
0.2V
PROTECT
L
30Hz 150Hz 0dB 10dB 6.0V
0.2V
LEVEL
HI PASS CH3/4 X-OVER
LOW PASS
LEVEL
HI FULL LP
30Hz 150Hz
6V
0.2V
PROTECT
0.2V
POWER
2CH 4CH 5CH
LEVEL
CH5
MODE
SUB
REMOTE
BASS EQ
SONIC
LOW PASS
POWER
PROTECT
180
0dB
10dB
15Hz
35Hz 35Hz 250Hz
POWER
SUB
PROTECT
IN
SONIC
LOW PASS
0dB
10dB
15Hz
35Hz 35Hz 250Hz
OUTPUT
MASTER
INPUT
SLAVE
OUT
Ch5