Hifonics TMA2000.4 Manual de instalación de inicio rápido

Navegue en línea o descargue pdf Manual de instalación de inicio rápido para Amplificador Hifonics TMA2000.4. Hifonics TMA2000.4 2 páginas.

Imprimir página
Hifonics TMA2000.4 Manual de instalación de inicio rápido
INPUT
INPUT
SUBSONIC
SUBSONIC
LEVEL
LEVEL
Setup
15
35Hz
10
40Hz
9V
0.2V
6V
0.2V
The input MODE switch will select how the signal input
A
is distributed to the different channels. If you have signal
PHASE
LPF
LPF
LPF
INPUT
INPUT
INPUT
INPUT
cables for front and rear channels, set the switch to 4CH.
Input Mode
LEVEL
LEVEL
LEVEL
SUBSONIC
LEVEL
Additionally if you have a dedicated subwoofer signal you
can use the 5CH setting(TMA-800.5 only). Use the 6CH
setting when you have all 6 input cables(TMA-1000.6 only)
0
180
35
250Hz
30
250Hz
40
300Hz
15
35Hz
9V
0.2V
6V
9V
0.2V
0.2V
6V
0.2V
B
The XOVER Mode switch sets the type
BASS EQ
BASS EQ
HPF
HPF
of crossover that will be active. 4 channel
PHASE
LPF
LPF
PHASE
LPF
models will have two switches, one for each
Xover Mode
set of channels.
60
1.3KHz
60
1.2KHz
0
10dB
0
9dB
0
180
35
250Hz
30
250Hz
0
180
35
250Hz
C
The HPF(high pass filter) control will limit the
BASS EQ
BASS EQ
HPF
INPUT
INPUT
BASS EQ
BASS EQ
output below the selected frequency. This
LEVEL
LEVEL
High pass
is typically used to protect midrange and hi
frequency speakers from damage and to
Adjustment
60
1.3KHz
0
10dB
0
9dB
allow a smooth transition from a subwoofer.
0
10dB
0
9dB
9V
0.2V
6V
0.2V
D
The LPF(low pass filter) control
PHASE
LPF
will limit output above the selected
frequency. This is used to allow
Low pass
a smooth transition to the higher
Adjustment
frequency speakers.
0
180
35
250Hz
The Bass EQ control will increase the power
E
BASS EQ
BASS EQ
output at 45Hz for more pronounced bass.
Exercise caution when using this control.
Bass Boost
Increase the level in small amounts until
0
10dB
0
9dB
distortion is noticed, then back off a little.
F
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
Remote Level
Control
G
This is a critical step to insure your amplifier
is properly adjusted to match the signal
output level of your source unit.
Level Setting
THIS IS NOT A VOLUME CONTROL!
1.
If possible, with the source unit off, confirm that the primary volume control is
turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or "0" adjustment. Make sure that the green LED on
the end of the amplifier is illuminated.
3.
Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier level (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple amplifiers.
XOVER
MODE
FULL
HP
MONO STEREO
LP
XOVER
MODE
XOVER
MODE
XOVER
MODE
SUBSONIC
SUBSONIC
SUBSONIC
MONO STEREO
FULL LPF HPF
2CH
4CH
FULL
HP
MONO STEREO
FULL
HP
MONO STEREO
LP
10
40Hz
LP
15
35Hz
10
40Hz
MODE
XOVER
MODE
XOVER
MODE
LPF
LPF
LPF
4CH
2CH
FULL LPF HPF
MONO STEREO
FULL LPF HPF
MONO STEREO
40
300Hz
30
250Hz
40
300Hz
MODE
MODE
HPF
XOVER
MODE
HPF
HPF
XOVER
INPUT
INPUT
SUBSONIC
SUBSONIC
LEVEL
LEVEL
SUBSONIC
SUBSONIC
4CH
2CH
4CH
2CH
60
1.2KHz
FULL
HP
MONO STEREO
60
1.3KHz
60
1.2KHz
FULL
HP
LP
15
35Hz
10
40Hz
LP
9V
0.2V
6V
0.2V
15
35Hz
10
40Hz
XOVER
MODE
LPF
LPF
XOVER
PHASE
LPF
LPF
LPF
FULL LPF HPF
MONO STEREO
30
250Hz
40
300Hz
FULL LPF HPF
0
180
35
250Hz
30
250Hz
40
300Hz
MODE
HPF
HPF
BASS EQ
BASS EQ
HPF
HPF
4CH
2CH
60
1.3KHz
60
1.2KHz
0
10dB
0
9dB
60
1.3KHz
60
1.2KHz
XOVER
INPUT
INPUT
LEVEL
LEVEL
SUBSONIC
SUBSONIC
FULL
HP
15
35Hz
10
40Hz
LP
9V
0.2V
6V
0.2V
XOVER
PHASE
LPF
LPF
LPF
FULL LPF HPF
0
180
35
250Hz
30
250Hz
40
300Hz
BASS EQ
BASS EQ
HPF
HPF
0
10dB
0
9dB
60
1.3KHz
60
1.2KHz
MODE
MONO STEREO
MODE
MONO STEREO
MODE
4CH
2CH
MODE
MONO STEREO
MODE
MONO STEREO
MODE
4CH
2CH

Quick Start

Installation Guide

TMA-400.4
TMA-800.5
TMA-1000.6
TMA-2000.4
Congratulations on your choice of a Hifonics amplifier.
This "Quick Start Installation" guide is meant to help you
"hook up" and play music.