ADENDORFF MAC AFRIC SDRILC-024 Instrucciones de uso originales - Página 4

Navegue en línea o descargue pdf Instrucciones de uso originales para Martillo Rotativo ADENDORFF MAC AFRIC SDRILC-024. ADENDORFF MAC AFRIC SDRILC-024 11 páginas. Cordless brushless rotary hammer

Imprimir página

2. Check the tool and battery carefully before putting it into use. Stop operation immediately

when malfunctions be found and send the tool to be repaired by qualified serviceman. Do

not open the tool yourself.

3. Use only original MAC AFRIC SBATTR-002/004 type rechargeable Li-Ion battery for this

tool and recharge only with the MAC AFRIC SBATTR-002/004 type charger supplied with

the tool. Use of other type of battery or charger, e.g. imitated, modified or with other

brand, may result in a risk of battery burst causing personal injury and property damage.

4. Keep your hands and clothes far away from the drill chuck, or it may clamp your fingers

and clothes.

5. Always be sure to have a firm footing and be sure no one is below when using the tool in

high locations.

6. Use the attached auxiliary handle. Misuse may cause personal injury and always be sure

to hold the tool firmly.

7. Keep the workplace well-ventilated and wear appropriate protective equipment based on

the operation to avoid personal injury.

8. Keep working area clean. Blends of materials are particularly dangerous. Dust from light

alloys can burn or explode.

9. Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held

more secure than by hand.

10. Do not touch the bit or parts close to the bit immediately after operation; they may be

extremely hot and could burn your skin

11. Damaged tools, accessories and deposed packages should be recycled in an

environmentally friendly way in accordance with the local law.

SAVE THESE INSTRUCTIONS.

WARNING! MISUSE or failure to follow the safety rules stated in this instruction manual may

cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY AND

CHARGER

Always set the reversing switch lever in the central position (lock the switch) and

remove the battery cartridge before tool change, inspection, maintenance,

transportation, storage or something like that.

Always check and confirm the battery cartridge is installed properly before use.

It's normal that the battery will become a little bit hotter while charging.

Do not charge for the damaged battery.

After charging, unplug the charger from power source and then remove the battery

cartridge from the charger. Do not leave the battery cartridge in the charger after the

charging cycle is completed.

Do not put the charged battery cartridge in the charger when the tool is not used.

Do not disassemble charger or battery; take it to a qualified serviceman when service or

repair is required; incorrect reassembly may result in a risk of electric shock or fire.

Do not short the battery cartridge.

Do not burn the battery. It will explode in a fire.

10.

Be careful not to drop, shake or strike the battery.

11.

Do not use battery as hammer. Knocking it may cause accidental short circuit, fire or

explosion.

12.

Keep battery far from fire and high temperature. Never place battery on radiator or

expose it under continuous sun irradiation. There is danger of explosion.

13.

Keep work area well-ventilated. Improper use of battery or damaged battery may send

out toxic gases, which can cause personal injury.

14. Overheating or overusing of the battery may cause liquid escape and come into contact

with the adjacent components. Clean such parts or replace them, if required. If electrolyte

contacts with your skin, wash the contacted area with soap firstly and then wash with

lemon juice and vinegar. If electrolyte gets into your eyes, rinse them out with clear water

and seek medical attention right away.

15. If operating time with a battery has become excessively shorter after charging, stop

operating immediately and replace with a new one or go to maintenance for inspection.

Continuous using of a worn out battery may result in a risk of overheating, possible burns

and even an explosion.