DC SD50 Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Lavavajillas DC SD50. DC SD50 2 páginas.

Imprimir página

USER GUIDE

POWER

LAMP

(OPTIONAL DRAIN PUMP)

REMOVE DRAIN PLUG THEN

SWITCH THE MACHINE OFF

TO START THE AUTOMATIC

DRAIN PUMP CYCLE

PREPARATION

• CHECK THE DRAIN PLUG IS PUSHED FIRMLY IN PLACE AND FILTERS ARE PROPERLY LOCATED.

• CHECK THE DETERGENT CHEMICAL (RED) AND RINSE AID CHEMICAL (CLEAR) SUPPLY TUBES - WITH FOOT VALVES ATTACHED ARE SUBMERGED IN SUFFICIENT

CHEMICAL. WHEN THE CHEMICAL IN THE CONTAINER IS LOW REPLACE WITH A FULL CONTAINER. DO NOT USE THE MACHINE IF THERE IS NO CHEMICAL.

• CHECK THE DOOR IS CLOSED AND PRESS THE POWER SWITCH - THE GREEN POWER LAMP WILL COME ON.

• WAIT FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE. THE MACHINE READY LAMP WILL COME ON.

OPERATION

• REMOVE ALL DEBRIS FROM THE ITEMS TO BE WASHED BEFORE PLACING THEM INTO THE BASKET.

• LOAD ITEMS INTO THE BASKET PROVIDED ENSURING NO ITEMS ARE COVERING EACH OTHER - PUSH THE BASKET INTO THE MACHINE.

• CLOSE THE DOOR - PRESS THE CYCLE START SWITCH - THE WASHING CYCLE WILL BEGIN AND THE WASH CYCLE LAMP WILL COME ON.

• AT THE END OF THE CYCLE THE WASH CYCLE LAMP WILL GO OUT - OPEN THE DOOR AND PULL OUT THE BASKET.

• ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING THE BASKET.

• CLOSE THE DOOR IF YOU ARE NOT WASHING TO CONSERVE TEMPERATURES .

WATER SOFTENER REGENERATION MODELS

• THE SALT LOW LAMP WHEN ON WARNS IF THE SALT CONTAINER IS LOW ON SALT OR EMPTY.

• UNSCREW THE SALT CONTAINER LID LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE SALT CONTAINER WILL REGENERATE

APPROXIMATELY FIVE REGENERATION CYCLES & HOLDS 500g OF SALT).DO NOT OVERSPILL, IF SALT IS SPILT ONTO STAINLESS STEEL RINSE THOROUGHLY WITH

WATER. ENSURE THE SALT CONTAINER LID IS SECURE AFTER FILLING.

• THE WATER SOFTENER REGENERATION CYCLE WILL BE FULLY AUTOMATIC AND WHEN REQUIRED STARTS AFTER THE FIRST FILL AND DURING THE INITIAL

HEATING OF THE MACHINE.

• THE REGENERATION LAMP WILL BE ON WHILE THE MACHINE CLEANS AND REGENERATES THE SOFTENER SYSTEM.

• THE MACHINE WASH CYCLE START IS DISABELED DURING THE 15 MINUTE REGENERATION. DO NOT SWITCH OFF THE MACHINE WHILE REGENERATING.

• WHEN REGENERATION IS COMPLETE THE WATER SOFTENER REGENERATION LAMP WILL GO OUT AND THE MACHINE WILL CONTINUE TO HEAT.

• WAIT FOR THE MACHINE TO REACH THE CORRECT WASHING TEMPERATURE. THE MACHINE READY LAMP WILL COME ON.

• THE MACHINE IS NOW READY TO START WASHING.

DRAIN PLUG

FILTER

LOWER SUMP

DC Products

(SXD MODELS ONLY)

WASH CYCLE

LAMP

SELECTION LAMP

CYCLE START

POWER

SWITCH

FOOT VALVE AND FILTER FOR

THE CHEMICAL TUBES

ED50 / SD45 / SXD45 / SD50 / SXD50

CYCLE TIME

(SXD MODELS ONLY)

CYCLE TIME SWITCH

2` 3` MINUTE

SALT CONTAINER LID

SALT

SALT CONTAINER

(SOFTENER MODELS)

REGENERATION LAMP

RINSE ARM RETAINING NUT

RINSE ARM

WASH ARM

A + IS + D

MACHINE

READY

LAMP

(SOFTENER MODELS)

SALT LOW LAMP

RINSE PIN