DC SXD45A D Manual del usuario - Página 2

Navegue en línea o descargue pdf Manual del usuario para Lavavajillas DC SXD45A D. DC SXD45A D 2 páginas.

Imprimir página

User Guide

POWER

LAMP

(OPTIONAL DRAIN PUMP)

REMOVE DRAIN PLUG THEN

SWITCH THE MACHINE OFF

TO START THE AUTOMATIC

DRAIN PUMP CYCLE

POWER

SWITCH

PREPARATION

 CHECK THE DRAIN PLUG IS PUSHED FIRMLY IN PLACE AND FILTERS ARE PROPERLY SECURED.

 CHECK THE DETERGENT CHEMICAL (RED) AND RINSE AID CHEMICAL (CLEAR) SUPPLY TUBES ‐ WITH FOOT VALVES ‐ ARE SUBMERGED IN SUFFICIENT PRODUCT.

 CHECK THE DOOR IS CLOSED AND PRESS THE POWER SWITCH ‐ THE GREEN POWER LAMP WILL COME ON.

 WAIT FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE. THE MACHINE READY LAMP WILL COME ON.

OPERATION

 REMOVE ALL DEBRIS FROM THE GLASSES TO BE WASHED BEFORE PLACING THEM INTO THE BASKET. PUSH THE BASKET INTO THE MACHINE.

 CLOSE THE DOOR ‐ PRESS THE CYCLE START SWITCH ‐ THE WASHING CYCLE WILL BEGIN AND THE WASH CYCLE LAMP WILL COME ON.

 AT THE END OF THE CYCLE THE WASH CYCLE LAMP WILL GO OUT ‐ OPEN THE DOOR AND PULL OUT THE BASKET.

 ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING THE BASKET.

DAILY CLEANING & MAINTENANCE

 AT THE END OF A SESSION TURN OFF THE POWER SWITCH. DO NOT REMOVE THE FILTER AT THIS STAGE.

 REMOVE THE DRAIN PLUG ‐ THE WASH TANK WILL EMPTY ‐ (MACHINES FITTED WITH DRAIN PUMP WILL AUTOMATICALLY START TO PUMP THE WATER OUT).

 COLLECT THE DEBRIS AND REMOVE FROM THE WASH TANK.

 CLEAN AROUND THE WASH TANK ‐ DOOR SURROUNDS AND HINGES WITH AN 'ADDIS'' TYPE WASHING UP BRUSH AND CLEANING CLOTH.

 DO NOT USE BLEACH OR CHLORIDE BASED CLEANING SOLUTIONS OR ABRASIVES WHEN CLEANING THE WASH TANK.

 TAKE OUT THE FILTER BOWL ‐ CLEAN THOROUGHLY AND REPLACE .

 DO NOT ALLOW DEBRIS TO GO DOWN THROUGH THE OUTLET HOLE AS THIS MAY DAMAGE YOUR MACHINE.

 REGULARLY CHECK RINSE JETS AND WASH JETS ARE CLEAR OF DEBRIS OR LIME SCALE ‐ REMOVE IF NECESSARY BY UNSCREWING THE RINSE ARM NUT THAT HOLDS

THE RINSE ARM IN PLACE ‐ REMOVE THE RINSE PIN THAT HOLDS THE WASH ARM IN PLACE ‐ CLEAN BOTH THOROUGHLY AND REASSEMBLE.

WATER SOFTENER REGENERATION

 THE SALT LOW LAMP WHEN ON WARNS IF THE SALT CONTAINER IS EMPTY.

 UNSCREW THE SALT CONTAINER LID LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE SALT CONTAINER WILL APPROXIMATELY

REGENERATE FOUR REGENERATION CYCLES & HOLDS 500g OF SALT).DO NOT OVERSPILL, ENSURE THE SALT CONTAINER LID IS SECURE AFTER FILLING.

 THE REGENERATION CYCLE SOULD BE STARTED AT THE END OF THE SERVICE WHEN THE MACHINE HAS BEEN IN USE, REMOVE THE DRAIN PLUG FROM THE

WASH TANK. THE WASH TANK WILL EMPTY. (THE DRAIN PLUG SHOULD BE REMOVED DURING THE 20 MINUTES REGENERATION)

 TURN THE MACHINE OFF. THE MACHINE POWER SWITCH MUST BE OFF TO ENABLE THE REGENERATION CYCLE SWITCH.

 CLOSE THE HOOD AND PRESS THE REGENERATION SWITCH FOR TWO SECONDS, THE WATER SOFTENER REGENERATION LAMP WILL COME ON.

 THE REGENERATION OF THE WATER SOFTENER WILL TAKE AROUND 20 MINUTES AND WILL BE FULLY AUTOMATIC.

 THE WATER SOFTENER REGENERATION LAMP WILL GO OUT AND THE MACHINE WILL SWITCH OFF AUTOMATICALLY AFTER THE REGENERATION

CYCLE IS COMPLETE. REMEMBER TO REPLACE THE DRAIN PLUG BEFORE RE‐FILLING THE MACHINE.

 MEDIUM‐WATER HARDNESS MAY REQUIRE FOUR REGENERATIONS A WEEK. MEDIUM TO HARD‐WATER HARDNESS MAY REQUIRE DAILY REGENERATION

RINSE ARM

RINSE

JETS

WASH ARM

SERVICE CALLS TO RECTIFY FAULTS CAUSED BY `THE LACK OF ROUTINE MAINTENANCE` WILL BE CHARGED FOR AND YOUR WARRANTY MAY BE AFFECTED

DC Products

SD45A IS D / SD50A IS D / SXD50A IS D / SXD45A IS D

WASH CYCLE

LAMP

CYCLE START

SWITCH

RINSE ARM NUT

FOOT VALVES FOR

CHEMICAL

CONTAINER TUBES

RINSE PIN

WASH JETS

(SXD MODELS ONLY)

REGENERATION

CYCLE TIME

SELECTION LAMP

LAMP

(SXD MODELS ONLY)

CYCLE TIME SWITCH

(REMOVE DRAIN PLUG DURING THE

2` 3` MINUTE

FILTER

BOWL

OUTLET HOLE

SALT LOW

MACHINE READY

LAMP

WATER SOFTENER

START SWITCH

REGENERATION)

SALT CONTAINER LID

DRAIN PLUG