AutoSat GPS-GPRS Video Manual de instrucciones - Página 5

Navegue en línea o descargue pdf Manual de instrucciones para Alarma de coche AutoSat GPS-GPRS Video. AutoSat GPS-GPRS Video 8 páginas. Satellite car alarm

Imprimir página

ENGLISH

.0. HOW AutoSat FUNCTIONS WITH AN ALARM TRIGGER

If the system detects an alarm trigger, it will execute the following procedure:

1) Acquisition and memorization of an image for each camera installed.

2) Telephone call to the memorized telephone numbers that have been enabled to receive

ring only in case of alarm trigger. If one of the numbers does not reply to the ring, the

system will attempt another 2 calls after it has terminated sending the SMS messages and

e-mail.

3) Transmission of SMS to the memorized telephone numbers that have been enabled to

receive ring in case of alarm trigger. The alarm message format is as follows:

99999999-Attention, alarm X! Info GPS: speed 2 km/h;

latitude 41,7112 north; longitude 12,6284 east

The number 99999999 is the factory programmed "ID" of the AutoSat and X=1,2,3, is the

number of the input terminal that has triggered the alarm.

4) Transmission of alarm e-mail, with real time images and the GPS acquisition with position

and speed. On the text of the e-mail is indicated the number of the alarm trigger.

NOTE

If it is impossible to send the e-mail, an SMS message will be sent to the

memorized telephone numbers with the reason of the e-mail failure (see

paragraph 6.0. on Page 13).

Alarm e-mail format

Page 12

AutoSat GPS - GPRS video instruction manual

.0. MESSAGE PROGRAMMING

The AutoSat may receive SMS command messages from any telephone number, but to

access, you need a password (indicated as PSW).

The unit is factory supplied with password 1234. It is possible to change this password of the

AutoSat by sending an SMS (see paragraph 3.2. at Page 7).

3.1. SMS message programming

To memorize the parameters of the SIM card (command "!PARA")

To transmit and receive e-mails, it is necessary to open an e-mail account for the SIM card

inserted in the AutoSat. To do this, you must contact the SIM card GSM company and

request an e-mail account to be assigned to the SIM card. After the e-mail account has

been assigned, you must send an SMS message to the AutoSat with the following

information:

E-mail address assigned to the SIM card (E-MAIL_SIM)

End user identification number for the internet connection (USERID)

Recognition password for connection to internet (INT_PSSW)

The SMS message will be as shown below:

!PARA#PSW#E-MAIL_SIM#USERID#INT_PASSW#

Example: If the system password is 1234 and you obtained from the tel. Co. the USERID

"brown" and the password "test", and the e-mail address is "[email protected]",

then the SMS message that must be sent is:

!PARA#1234#[email protected]#brown#test#

The AutoSat will send an SMS confirmation reply message to the telephone number that

has made the request.

AutoSat replies: PARA: [email protected], brown, test

To memorize and cancel the e-mail addresses (maximum 3) (command "!

MAIL")

To memorize in the AutoSat the e-mail address (maximum 29 characters) to which you

wish to send e-mails with photo images, it is necessary to send an SMS message to the

AutoSat as shown below:

!MAIL#PSW#option#address1#address2#address3#

where: option = 'A' is to receive the e-mail automatically in case of alarm or by request

option = 'B' to receive the e-mail only when requested

Example: !MAIL#1234#A#[email protected]#[email protected]#[email protected]

AutoSat replies: MAIL:[email protected]#[email protected]#[email protected]

To cancel the e-mail addresses memorized, send the following message:

!MAIL#PSW#C

Example: !MAIL#1234#C

AutoSat GPS - GPRS video instruction manual

ENGLISH

Page 5