Galls ST160 SIREN Manual de instrucciones de instalación y funcionamiento - Página 7
Navegue en línea o descargue pdf Manual de instrucciones de instalación y funcionamiento para Amplificador Galls ST160 SIREN. Galls ST160 SIREN 12 páginas. Siren amplifier
También para Galls ST160 SIREN: Manual de instrucciones de instalación y funcionamiento (7 páginas)
Imprimir página
(Installer Selectable Options CONT'D)
Tones For WAIL, YELP, and
THUNDER, and Thunder Step-Up
Function
1 WAIL (Wail default) §, *, †
2 YELP (Yelp default) §, *
3 THUNDER (THUNDER default)
TWO-TONE
(THUNDER Step Up
4
default)
5 MECHANICAL WAIL
(FIRE ENGINE)
6 MAX YELP §, *
7 HOOT
8 RAPID HOOT
9 AIR HORN & YELP
10 GHOST
11 RAPID GHOST
12 SINGLE AIR HORN
13 SINGLE QUICK
14 DOUBLE POST POP AIR HORN
15 TWO TONE AIR HORN
16 STANDARD AIR HORN
17 CONTINUOUS TONE
18 CONTINUOUS BEEP
§ = SAE approved
* = California Title 13 approved
† = See below
Wind Down or Hard Stop Option
By default, the Wail tones indicated by the "†" above will "wind down" when they
are de-activated. If you prefer to have them immediately stop (i.e. hard stop), hold
the Program Button for 3 seconds (until the LED flashes once). This will change it to a
hard stop. Repeat to change back to the wind down option.
Tone Disable Option
Some municipalities may ban the use of specific tones, such as the Thunder tone.
The Thunder Disable jumper option (found in our previous versions of the ST240) has
been replaced with the Optional Tone Programming feature described on the
previous page. This will allow you to reprogram the THUNDER default tone from
Thunder to any of the other tones listed. This new feature expands the former option
(that was previously limited only to disabling the Thunder tone) to the ability to
replacing ANY of the tones that may not be permitted (or desired).
Auxiliary-Manual Function Option
By default, when the siren is in THUNDER, YELP, or WAIL modes, and the AUX function
is activated (typically by the steering wheel horn relay), the siren will produce the
standard Air Horn Tone (#1 in the chart above) and temporarily override the siren
tone. If you would rather have the AUX function (i.e. steering wheel horn) mimic the
MANUAL button (see MANUAL button functions on page 7), then you should
program the AUX function for tone #9 (Manual) or #10 (Mechanical Manual).
Optional Tones
Tones For MANUAL Button & AUX Wire
1 STANDARD AIR HORN (AUX default)
2 LOW FREQUENCY AIR HORN
3 RAPID AIR HORN
4 AIR HORN II
5 DOUBLE POST POP AIR HORN
6 SINGLE AIR HORN
†
7 SINGLE QUICK AIR HORN
8 TWO TONE AIR HORN
9 MANUAL (MANUAL default) *
10 MECHANICAL MANUAL
(FIRE ENGINE)
►►►►
System Reset
If you would like to reset ALL of the siren programming
options to their defaults, activate any tone and press
the Program button for nine (9) seconds. The LED will
flash once, then twice, then three times, and all siren
tones will stop.
-5-
Tones for HORN Button
1 STANDARD AIR HORN (default)
2 LOW FREQUENCY AIR HORN
3 RAPID AIR HORN
4 AIR HORN II
5 DOUBLE POST POP AIR HORN
6 SINGLE AIR HORN
7 SINGLE QUICK AIR HORN
8 TWO TONE AIR HORN
◄◄◄◄