Maino Caldo Bello CB1 Instrucciones

Navegue en línea o descargue pdf Instrucciones para Accesorios Maino Caldo Bello CB1. Maino Caldo Bello CB1 2 páginas.

The linked image cannot be display ed. The file may hav e been mov ed, renamed, or deleted. V erify that the link points to the correct file and location.

ATTENTION!

a. The lamp should be hung from above. It should not be supported on boxes, cages

or any other kind of object. Neither should it be placed on the ground in direct

contact with the floor or with the animals.

b. MAKE SURE THE ELECTRIC POWER CABLE IS A WAYS OUT OF REACH OF THE

LIVESTOCK.

c. Attention: Please ensure that liquid does not come in contact with the

heater or bulb.

Hook a chain or a cable on the eyelets on the back of the lamp:

For chicks of hen, pheasant, duck, goose, bantam, turkey, quail, grey partridge and red partridge: hang the

lamp at ca. 50 cm. from the ground up to 20 days from their birth;

For chicks of Ratite (Ostrich, Emu and Rhea): hang the lamp at ca. 70 cm. from the ground up to 20 days

from their birth.

BEFORE CONNECTING THE APPLIANCE TO THE ELECTRICITY LINE AND/OR SWITCHING IT ON READ THE

FOLLOWING CAREFULLY. THE MAKER DOES NOT TAKE ANY RESPONSIBILITY FOR INJURIES OR FOR DAMAGES

THAT MIGHT OCCUR TO PEOPLE AND TO THE HEAT LAMP DUE TO LACK OF ATTENTION TO THE FOLLOWING

PROCEDURE. MAKE SURE THAT THE VOLTAGE IS THE SAME OF THE ONE WRITTEN ON THE TECHNICAL

INFORMATION PLATE. IF THE ELECTRIC INFORMATION PLATE STATES A DIFFERENT VOLTAGE CONTACT YOUR

DEALER. DO NOT CONNECT THE POWER CORD TO THE ELECTRICITY LINE AND DO NOT SWITCH ON THE

APPLIANCE ON. MAKE SURE THAT THE PLUG OF THE HEAT LAMP YOU USE TO CONNECT TO THE ELECTRICITY

LINE IS SUITABLE TO THE SOCKET YOU WANT TO USE; IF IT IS NOT SO CONTACT YOUR DEALER. DO NOT TRY

TO CHANGE THE PLUG BY YOURSELF, OTHERWISE THE GUARANTEE CERTIFICATE IS NOT VALID ANYMORE.

SWITCHING ON OF THE APPLIANCE: AFTER HAVING CHECKED ALL THE DIRECTIONS LISTED ABOVE AND ONLY

IN THE CASE THAT NO FURTHER INTERVENTIONS ARE NECESSARY PUT THE PLUG IN THE SOCKET to SWITCH

ON THE APPLIANCE. To switch off the appliance disconnect the plug from the socket.

PLEASE ENSURE THE PLUG IS REMOVED FROM THE ELECTRICAL SOCKET BEFORE

ATTEMPTING ANY MAINTAINANCE/CLEANING ON THE HEAT LAMP .

Place a thermometer (optional accessory not provided with the lamp) below the lamp and adjust the

temperature with the knob on the upper part of the lamp. Rotate it clockwise to increase it and anti-clockwise

to decrease it until you reach the required temperature. Once you finish the adjustment: Remove the

thermometer, place it in the proper case and keep it carefully for next use.

E LE C TRI C FE AT URE S : B RI T I S H P LUG 2P O L E+ E – 1 3 A . FU S E – NO R M SC O D E: BS 1363A/95

DO NOT DISASSEMBLE THE BUFFLE AND THE PROTECTION NET. DO NOT REMOVE OR

TOUCH THE INFRARED LAMP WITH YOUR HANDS. THERE IS GREAT DANGER OF BURN AND

DANGER OF BREAKING THE HEATING ELEMENT! ATTENTION: IT IS AN HALOGEN LAMP AT

HIGH TEMPERATURE COVERED WITH A SPECIAL INFRARED FILTER. DO NOT IMMERSE THE

STRUCTURE OR THE LAMP INTO WATER, DO NOT WET IT AND DO NOT WASH IT. CLEAN DRY

USING A BRUSH OR COMPRESSED-AIR.

Call the technical assistance. Together with the heating bulb you will receive the instructions to change it.

Infrared heating lamp

CALDO BELLO CB1, CB2, CB3, CB4

INSTALLATION OF THE LAMP:

ELECTRIC CONNECTION:

HOW TO ADJUST TO THE REQUIRED TEMPERATURE:

TE CH NI C AL F E ATU RE S:

TE N SIO N: 2 30 Va c + 10 /- 15 %

TO TAL P OW ER C B 1 A ND C B 2: 0 .2 5 KW – C B 3 A N D CB 4: 0. 5 KW

HOW TO CHANGE THE LAMP:

C A L DO B E LLO H E AT LA M P

;

F R E Q UE NC Y: H z. 5 0 ±0, 5 %