HIKOKI C361396M Manual de instrucciones de manipulación - Página 8

Navegue en línea o descargue pdf Manual de instrucciones de manipulación para Taladro HIKOKI C361396M. HIKOKI C361396M 16 páginas.

Imprimir página

LUBRICATION

This Rotary Hammer is of full air-tight construction to protect

against dust.

Therefore, this Rotary Hammer can be used without

lubrication for long periods. Replace the grease whenever

you change the carbon brush to maintain the service life.

Further use of the rotary hammer with lock oﬀ grease will

cause the machine to seize up reduce the service life.

CAUTION

A special grease is used with this machine, therefore,

the normal performance of the machine may be badly

aﬀ ected by use of other grease. Please be sure to let

one of our service agents undertake replacement of the

grease.

MAINTENANCE AND INSPECTION

1. Inspecting the tools

Since use of a dull tool will cause motor malfunctioning

and degraded eﬃ ciency, replace the tool with new ones

or resharpen them without delay when abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very "heart" of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement on

this machine should ONLY be performed by a HiKOKI

Authorized Service Center.

5. Replacing supply cord

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer of this agent in order

to avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 102 dB (A)

Measured A-weighted sound pressure level: 94 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Hammer drilling into concrete:

Vibration emission value

Uncertainty K = 1.5 m/s

Equivalent chiselling value:

Vibration emission value

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diﬀ er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI's continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

h , HD = 14.7 m/s

h , CHeq = 14.0 m/s