HIKOKI FD 10VA Manual de instrucciones de manipulación - Página 4
Navegue en línea o descargue pdf Manual de instrucciones de manipulación para Taladro HIKOKI FD 10VA. HIKOKI FD 10VA 20 páginas.
Imprimir página
English
PRECAUTIONS ON USING DRILL
1. When mounting the drill bit or driver bit, insert it
fully into the drill chuck and completely tighten the
drill chuck with the chuck wrench.
If mounting is not done porperly, it is very dangerous
as the drill bit may slip or loosen during operation.
2. Do not wear gloves made of stuff liable to roll up
such as cotton, wool, cloth or string, etc.
SPECIFICATIONS
Model
Voltage (by areas)*
Power Input
No-load speed
Steel
Capacity
Wood
Weight (without cord)
*Be sure to check the nameplate on product as it is subject to change by areas.
APPLICATIONS
1. Drilling various materials
○ Drilling metal
Use an iron-working drill bit
○ Drilling wood
Use a wood-working drill bit (However, an iron-
working drill bit to make pilot holes for wood screws
or holes smaller than 6.5 mm.)
2. Tightening the wood screw (Only FD10VA model)
Use the driver bit. Use a Phillips screw for easy
tightening.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of suffi cient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Check the tightening of the drill chuck
The drill chuck has been tightened at the factory, but
check again that it is in order before use.
Turn the drill chuck clockwise to tighten.
HOW TO USE
1. Operation of switch
Pulling the trigger of switch and push the stopper, it
keeps, the switched-on condition and it is convenient
for the continuous running. When switched off, the
stopper can be disconnected by means of pulling the
trigger again.
3
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
4. When placing the drill on the fl oor, make sure that
the drill has stopped completely.
5. Hold the drill fi rmly with both hands when using.
6. Before drilling into a wall, fl oor or ceiling, thoroughly
confi rm that no items such as electric cables or
conduits are buried inside.
7. When working in high position, take care of
downword direction.
FD10SA
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
235 W*
2300 /min
10 mm
18 mm
1.1 kg
2. Adjustment of speed
[FD10SA]
The maximum speed can be obtained by pulling the
trigger switch.
[FD10VA]
(1) The speed is adjustable from zero to maximum
speed according to the extent the trigger switch is
pulled.
(2) The maximum speed is adjustable from zero to
2300/min with the rotation of adjusting knob.
(3) Turn the adjusting knob clockwise for higher speed
and anticlockwise for lower speed. (Approximately
three rotations consist one full rotation of the
adjustment knob.) (Fig. 1)
(4) The switch can be locked with the stopper at any
required position irrespective as to how far the
adjusting knob has been rotated. Select a proper
position according to the required speed for each
work.
3. Confi rm the direction of bit rotation (Fig. 2)
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the reversing switch
lever. The L-side of the lever is pushed to turn the bit
counterclockwise.
CAUTION
Never change the direction of bit rotation while
operatihg. Turn the power switch OFF before
changing the direction of bit rotation; otherwise,
burning of the motor will result.
4. For use as a drill
(1) Mounting drill bit
Tighten drill bit with the chuck wrench. There are
three holes in which the chuck wrench should be
inserted. Tighten them equally in turn at three
holes, without tightening them only at one hole. The
drill bit can be removed in the opposite method as
mentioned above. (Fig 3)
(2) How to drill
1 To use for drilling lumber
○ Apply the point of the drill bit to the desired drilling
position, hold the drill perpendicular to the workpiece
surface and turn on the switch.
FD10VA
0 – 2300 /min