HIKOKI WR 18DSDL Manual de instrucciones de manipulación - Página 7

Navegue en línea o descargue pdf Manual de instrucciones de manipulación para Destornillador de impacto HIKOKI WR 18DSDL. HIKOKI WR 18DSDL 16 páginas.

Imprimir página
HIKOKI WR 18DSDL Manual de instrucciones de manipulación
● Regarding the temperatures and charging time of the battery.
The temperatures and charging time will become as shown in Table 2.
Battery
Charging voltage
Weight
Temperatures at which the battery can be
recharged
Charging time for battery capacity, approx.
(At 20oC)
1.3Ah
1.5Ah
2.0Ah
2.5Ah
3.0Ah
4.0Ah
5.0Ah
6.0Ah
Number of battery cells
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used,
the pilot lamp of UC18YFSL/UC18YKSL charger lights
for 1 second, does not light for 0.5 seconds (off for 0.5
seconds), or the charge indicator lamp of UC18YSL3
charger lights for 0.3 seconds, does not light for 0.3
seconds (off for 0.3 seconds). In such a case, fi rst let the
battery cool, then start charging.
○ When the pilot lamp or charge indicator lamp fl ickers in
red (at 0.2-seconds intervals), check for and take out
any foreign objects in the charger's battery connector. If
there are no foreign objects, it is probable that the battery
or charger is malfunctioning. Take it to your authorized
Service Center.
○ Since the built-in micro computer takes about 3 seconds
to confi rm that the battery being charged with chargers
are taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
○ If the pilot lamp or charge indicator lamp does not blink
in red (every second) even though the charger cord is
connected to the power, it indicates that the protection
circuit of the charger may be activated.
Remove the cord from the power and then connect
it again after 30 seconds or so. If this does not cause
the pilot lamp or charge indicator lamp to blink in red
(every second), please take the charger to the HiKOKI
Authorized Service Center.
Table 2
Charger
UC18YKSL
V
kg
0.35
min.
35
min.
40
min.
60
min.
75
min.
90
min.
120
min.
150
min.
180

MOUNTING AND OPERATION

MAINTENANCE AND INSPECTION

1. Inspecting the driver bit (WH14DSDL / WH18DSDL)
2. Inspecting the socket (WR14DSDL / WR18DSDL)
7
UC18YFSL
14.4V - 18V
0.5
0oC – 50oC
20
22
30
35
45
60
75
90
4 – 10
Action
Removing and inserting the
battery
Charging
Change rotation speed
Removing and mounting the hook
Remaining battery indicator
How to use the LED light
Mounting the bit
Mounting the socket
Reversing the rotational direction
Switch operation
Check and replacing the carbon
brush
Charging a USB device from an
electrical outlet
Charging a USB device and
battery from an electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
Using a broken bit or one with a worn out tip is dangerous
because the bit can slip. Replace it.
A worn or deformed hex. or a square-holed socket will
not give an adequate tightness to the fi tting between
the nut or anvil, consequently resulting in loss of
tightening torque. Pay attention to wear of a socket holes
periodically, and replace with a new one if needed.
UC18YSL3
0.6
-10oC – 50oC
15
15
20
25
20
26
32
38
Figure
Page
1
10
2
10
3
10
4
10
5
11
6
11
7
11
8
11
9
11
10
11
11
12
12-a
12
12-b
12
13
12
14
12
―
13