Bristan COB SHC3STP C (D9) Instrucciones de instalación y manual del usuario

Navegue en línea o descargue pdf Instrucciones de instalación y manual del usuario para Productos de fontanería Bristan COB SHC3STP C (D9). Bristan COB SHC3STP C (D9) 2 páginas.

Imprimir página

Specifications

Cold Water Supply

Dynamic Water Pressure

Min: 0.2 bar

Max: 5.0 bar

3.0

2.0

4.0

1.0

5.0

Min: 5°C Max: 25°C

Pressure

BAR

IMPORTANT

Maximum Static Pressure: 10.0 bar

Tools You'll Need

Flat head

Socket Spanner

Drill

Adjustable Spanner

Screwdriver

Prior to Installation

All products manufactured and supplied by Bristan are safe to use

provided that they are installed, operated and receive regular

maintenance in accordance with these instructions.

This product needs to be installed in accordance with, and meet the

requirements of the Water Supply (Water Fittings) Regulations 1999

and current by-laws. For full Installation Requirements & Notes (IRN)

please visit wras.co.uk/directory.

Isolation valves must be fitted to the inlet water supplies to ensure ease

of future maintenance. Before installing this product the water supply

must be thoroughly flushed in order to remove any swarf, solder etc.

Full access must be made available for future maintenance/

servicing purposes.

Before drilling into walls, check that there are no hidden electrical

wires, cables or water supply pipes. This can be checked with the

aid of an electronic detector.

If power tools are used do not forget to:

- Wear eye protection

- Unplug equipment after use

This product must not be modified in any way

as this will invalidate the guarantee.

If in doubt, contact a registered plumber, your Local Water

Authority or the Secretary of the Institute of Plumbing,

address as follows:-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex,

RM12 6NB, Tel: 01708 472791

Installation Instructions

& User Guide

Please leave these instructions

with the end user

Product Code: COB SHC3STP C (D9)

Inlet Water Temperature

Inlet Dimensions

Hot Water Supply

65°C

25°C

5°C

65°C Recommended

The inlet hot water must

be at least 10°C above the

required blend temperature.

Pipe Cutter

Silicon Sealant

Hexagonal Keys

Cavity Dimensions (mm)

Cavity Depth: 35mm

Concealing Plate

Adjustment Range: 15mm

Pack Contents

Valve Configuration

Yellow Flow

Limiter (Hot)

Installation

150

Centres

Inlet Connections

15mm

Compression

Prepare the pipework.

Create the rear access point in the

back of the wall cavity.

Pipe & Wire Detector

Hot

120

Connect the inlet

pipes ensuring the

olives are fitted.

Fit the handles.

Decrease

Temperature

Green Flow

Limiter (Cold)

Remove the inlet elbows and filters.

Remove the plastic inserts from the valve

inlets and insert the flow regulators.

Replace the elbows, ensuring the

filters are fitted.

Max 60mm

Install suitable

batons

(if required) onto

the rear cavity.

Mark the position

of the valve

Min 35mm

and drill and plug

Batons

holes to suit.

Plumb the

valve into your

chosen outlets.

Cold

Temperature Adjustment

Turn the handle to the

maximum temperature

setting, then remove it.

2.5

Turn the spindle

to increase or

decrease the

temperature.

Check the

temperature and

Fit the temperature

handle back in the

adjust until you

Increase

maximum hot position.

achieve the

Temperature

desired result.

Screw the

shrouds

onto the

valve.

Secure the valve using the

screws supplied (solid walls

only) or a suitable alternative.

Draw around

the concealing

plate as a template,

measuring in by

10mm to give

clearance. Finish the

wall surface. Using a

silicon sealant, push

on the concealing

plate and hold

firmly until set.

2.5