Bristan N2 SHC3STP G Instrucciones de instalación y manual del usuario

Navegue en línea o descargue pdf Instrucciones de instalación y manual del usuario para Productos de fontanería Bristan N2 SHC3STP G. Bristan N2 SHC3STP G 2 páginas.

Imprimir página

Specifications

Cold Water Supply

Dynamic Water Pressure

Min: 0.2 bar

Max: 5.0 bar

2.0

3.0

2.0

3.0

1.0

4.0

1.0

4.0

5.0

Min: 5°C Max: 25°C

Pressure

BAR

IMPORTANT

Maximum Static Pressure: 10.0 bar

Tools You'll Need

Flat head

Socket Spanner

Drill

Adjustable Spanner

Screwdriver

Prior to Installation

All products manufactured and supplied by Bristan are safe to use

provided that they are installed, operated and receive regular

maintenance in accordance with these instructions.

This product needs to be installed in accordance with, and meet the

requirements of the Water Supply (Water Fittings) Regulations 1999

and current by-laws. For full Installation Requirements & Notes (IRN)

please visit wras.co.uk/directory.

Isolation valves must be fitted to the inlet water supplies to ensure ease

of future maintenance. Before installing this product the water supply

must be thoroughly flushed in order to remove any swarf, solder etc.

Full access must be made available for future maintenance/

servicing purposes.

Before drilling into walls, check that there are no hidden electrical

wires, cables or water supply pipes. This can be checked with the

aid of an electronic detector.

If power tools are used do not forget to:

- Wear eye protection

- Unplug equipment after use

This product must not be modified in any way

as this will invalidate the guarantee.

If in doubt, contact a registered plumber, your Local Water

Authority or the Secretary of the Institute of Plumbing,

address as follows:-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex,

RM12 6NB, Tel: 01708 472791

Installation Instructions

& User Guide

Please leave these instructions

with the end user

Product Code: N2 SHC3STP G (D9)

Inlet Water Temperature

Inlet Dimensions

Hot Water Supply

65°C

25°C

5°C

65°C Recommended

The inlet hot water must

be at least 10°C above the

required blend temperature.

Pipe Cutter

Silicon Sealant

Hexagonal Keys

Pipe & Wire Detector

Cavity Dimensions (mm)

Cavity Depth: 35mm

Concealing Plate

Adjustment Range: 30mm

Pack Contents

Valve Configuration

Yellow Flow

Limiter (Hot)

Installation

150

Centres

Install suitable

batons

Inlet Connections

(if required) onto

the rear cavity.

Mark the position

15mm

of the valve

Compression

and drill and plug

holes to suit.

Crosshead

Screwdriver

Hot

120

Connect the inlet

pipes ensuring the

olives are fitted.

Fit the handles.

Decrease

Temperature

Green Flow

Limiter (Cold)

Remove the inlet elbows and filters.

Remove the plastic inserts from the valve

inlets and insert the flow regulators.

Replace the elbows, ensuring the

filters are fitted.

Max 45mm

Secure the valve

screws supplied

(solid walls only)

or a suitable

alternative.

Min 35mm

Batons

Plumb the

valve into

your chosen

outlets.

Cold

Temperature Adjustment

Turn the spindle

to increase or

decrease the

temperature.

Check the

Increase

Temperature

temperature and

adjust until you

achieve the

desired result.

Screw the

shrouds

onto the

valve.

using the

Draw around

the concealing

plate as a template,

measuring in by

10mm to give

clearance. Finish the

wall surface. Using a

silicon sealant, push

on the concealing

plate and hold

firmly until set.

Turn the handle to the

maximum temperature

setting, then remove it.

Fit the

temperature

handle back

in the

maximum

hot position.