Bristan Crosshead DUX DSM C Instrucciones de montaje y lista de contenidos - Página 3
Navegue en línea o descargue pdf Instrucciones de montaje y lista de contenidos para Cocina & Accesorios de baño Bristan Crosshead DUX DSM C. Bristan Crosshead DUX DSM C 5 páginas. Design utility kitchen ranges
Imprimir página
Sink Mixer
Sink Mixer
Sink Mixer
Sink Mixer
1. Identify all components and check for completeness, particularly before
arranging fitting.
2. Fit the mixer (3) to the sink using the fixing kit (10).
3. Screw in connecting copper tail pipes (11) by hand into base of the mixer and
then connect to the hot and cold supplies.
NOTE: A non return valve is supplied, which is designed to prevent back feeding
NOTE:
NOTE:
NOTE:
into the hot mains supply. An additional non return valve (not supplied) will be
required for the cold supply.
4. Fully open both valves, letting it run for a few minutes to check all connections
4. Fully open both valves, letting it run for a few minutes to check all connections
for leaks.
Contents
Contents
Contents
Contents
3. Body
4. Valve
5. Handle
6. Handle Screw
7. Indices
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT - - - - PLEASE READ
PLEASE READ
PLEASE READ
PLEASE READ
These fittings need to be installed in accordance with the following Installation Requirements and Notes
These fittings need to be installed in accordance with the following Installation Requirements and Notes
These fittings need to be installed in accordance with the following Installation Requirements and Notes
These fittings need to be installed in accordance with the following Installation Requirements and Notes
(IRN) to ensure they meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and the
(IRN) to ensure they meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and the
(IRN) to ensure they meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and the
(IRN) to ensure they meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and the
Scottish Byelaws 2004.
Scottish Byelaws 2004.
Scottish Byelaws 2004.
Scottish Byelaws 2004.
IRN R001 (DUL / DUC / DUX HNK / SNK DSM C)
IRN R001 (DUL / DUC / DUX HNK / SNK DSM C)
IRN R001 (DUL / DUC / DUX HNK / SNK DSM C)
IRN R001 (DUL / DUC / DUX HNK / SNK DSM C)
See text of entry for Installation Requirements or Notes.
IRN R006 (DUL / DUC / DUX HNK / SNK / DSM C)
IRN R006 (DUL / DUC / DUX HNK / SNK / DSM C)
IRN R006 (DUL / DUC / DUX HNK / SNK / DSM C)
IRN R006 (DUL / DUC / DUX HNK / SNK / DSM C)
This tap or combination tap assembly has a Type AUK3 air gap and is therefore for installation in any premises to
protect against a backflow risk up to a Fluid Category 5.
IRN R010 (DUL / DUC / DUX SNK / DSM C)
IRN R010 (DUL / DUC / DUX SNK / DSM C)
IRN R010 (DUL / DUC / DUX SNK / DSM C)
IRN R010 (DUL / DUC / DUX SNK / DSM C)
Water supplies shall be a reasonably balanced pressures from a common source (e.g. hot and cold supplies
both from the same storage or both from a supply pipe). Where the fitting is supplied from unbalanced supplies
(e.g. hot and cold supplies from separate sources) a Listed' single check valve or some other no less effective
backflow prevention device shall be fitted immediately upstream of both hot and cold water inlets.
x1
10. Fixing kit
x2
11. Tail pipes
x2
12. Shrouds
x2
16. Grub screw
x2
17. Non-Return Valve
Contents
Contents
Contents
Contents
1.
Backnut
2.
Backnut Washer
3.
Body
4.
Valve
5.
Handle
6.
Handle Screw
7.
Indices
x1
x2
x2
x1
x1
Schedule 2- - - - 15 (1)
Schedule 2
15 (1)
Schedule 2
Schedule 2
15 (1)
15 (1)
x2
x2
x1
x2
x2
x2
x2