Decko 24000-DKO Manual del usuario - Página 14

Navegue en línea o descargue pdf Manual del usuario para Abrepuertas de garaje Decko 24000-DKO. Decko 24000-DKO 14 páginas. Handles doors 18 ft. wide & up to 7ft.tall

Imprimir página

1. Operating the Opener

Connecting Wall Panel

To prevent SERIOUS INJURY or DEATH from electrocution:

- Power MUST NOT be connected until instructed.

To prevent SERIOUS INJURY or DEATH from using the Wall Panel or Push Button and a closing door:

- Install the Wall Panel or Push Button within sight of the door at a minimum height of 5 feet (1.5m)

above the floor. Make sure it is out of the reach of children and moving parts of door and hardware.

- NEVER permit children to access the Wall Panel, Push Button or remote Transmitters.

- Operate the door ONLY when it is adjusted properly with no obstructions present and is in clear sight.

- ALWAYS keep a moving door in sight until it's completely closed.

- NEVER cross the path of a moving door.

Arrow icon points UP

Drywall Anchor

Screw #6 x1"

Wall Panel

Min. 5 feet (1.5m) above floor

WARNING

The Wall Panel is a wired, illuminated door control placed inside

your garage.

To install the Wall Panel:

Inside your garage, install the rear cover of the Wall Panel

within sight of the door at a minimum height of 5 feet

(1.5m) off the ground. Ensure it is installed out of the reach

of children and free from the moving parts of the door and

hardware.

With the "Arrow" icon on the rear cover pointing to up, se-

curely fasten it to a solid surface with 1" screws. If attach-

ing to drywall or other hollow surface, drill 3/16" holes and

use the provided Drywall Anchors.

Snap the Wall Panel onto the rear

cover.

To Connect the Wall Panel to the Opener

Connect the pair of wires from the Wall Panel to the "Wall Box"

terminals on the rear of the Opener.

Wall

Box

From Wall Panel

Using the Wall Panel

(ONLY after installation is completed and power is connect-

ed as instructed.)

Door—Momentary press to access the door

Light– Turns the courtesy light On/Off

Vacation Lock

OFF — Door can be accessed by either access controls

ON — Prevent access of door by Remote Transmitters

and Door button

Connecting Power

To prevent SERIOUS INJURY or DEATH from electrocution or fire:

- Power MUST be DISCONNECTED BEFORE proceeding with permanent wiring procedures.

- Garage Door Opener installation and wiring MUST be in compliance with all local electrical and building

codes. Make sure the Opener is ALWAYS grounded.

- NEVER use an extension cord, 2-wire adapter or modify the power plug in any way to make it fit the outlet.

Ordinary Power Connection

For Permanent Wiring ONLY

Conduit with wire

Ground screw (green)

Line (B )

Neutral (W)

Ground (G)

Wire nut

Aligning the Photo Eye Safety System

To prevent SERIOUS INJURY or DEATH from a closing garage door:

- The Photo Eye Safety System MUST be installed BEFORE connecting power.

- The Photo Eye Safety System MUST be properly connected and aligned BEFORE operating the Opener.

Invisible Light Beam

WARNING

DO NOT OPERATE OPENER AT THIS TIME.

To Connect Power

Plug the Opener into a grounded outlet ONLY. If there is no

grounded outlet present, call a qualified electrician to replace the

outlet.

Permanent Wiring (If Required by Local Code)

Remove the enclosure by removing the 6 screws located

on the sides and rear of the Opener.

Cut the two wire connectors found inside and remove the

power cord.

Group neutral (white) wires from power source with 2 white

(W) wires and 1 yellow (Y) wire inside the Opener.

Connect them with a wire nut (not provided).

Group line (black) wires from power source with black wire

(B) inside the Opener. Connect them with a wire nut

(not provided).

Secure the ground (green or bare) wire from the power

source with a grounding screw.

Reinstall the enclosure.

Turn on power supply. If the wiring is properly connected,

a "click" should be heard and the light will illuminate (if a

bulb is installed). If there is no response from the Opener,

check power source and wiring.

WARNING

To Align the Photo Eye Safety System:

When the Photo Eye System is properly connected and the

power is connected, one of the Photo Eyes will emit a

steady green light. This Photo Eye is the Emitter that

generates the Invisible Light Beam.

When properly aligned, the Sensor should emit a steady

red light when it senses the invisible light beam from the

Emitter.

If the indication is unsteady, flashes or is dim, check for

any obstructions and adjust the position until the Sensor

gives a STEADY RED LIGHT.

Note: The path of the invisible light beam MUST NOT be

obstructed. No part of the garage door or any

hardware should interfere with the beam or the Open-

er will not close the door.