DECKORATORS ALX CLASSIC Instrucciones de instalación

Navegue en línea o descargue pdf Instrucciones de instalación para Mobiliario exterior DECKORATORS ALX CLASSIC. DECKORATORS ALX CLASSIC 3 páginas. Complete kit
También para DECKORATORS ALX CLASSIC: Instrucciones de instalación (4 páginas)

Imprimir página

• Drill/power screwdriver

• Miter or circular saw

with carbide tip blade

• Marked speed square

• Carpenter's level

• Carpenter's pencil

(1)

Top Rail

Bottom Rail

2 – 6' or 8' aluminum rails with baluster connectors installed

1 – Level or stair bracket kit

16 – #8 x 3/4" screws (8 - #8 x 3/4"and 8 - #8 x 1-3/4" screws for stair kits)

15 – Balusters (12 for stair kits, 20 for 8' line kits)

2 – Rail supports (3 for 8' kits)

NOTE: Recommend 5/16" x 4" or longer lags

In-Line Railing Installation Instructions

Posts Installation

Prior to construction:

• Check with your local regulatory agency for special code requirements in your area.

Common railing height is 36" or 42". Read instructions completely to get an understanding of

how the product goes together and how each piece affects the other.

• Determine the number of railing posts needed for your deck. Post spacing is 6' or 8' on-

center. Example: A 12' x 16' deck attached to a building with a 4' access opening on one side

will need a total of eight posts. To minimize cutting, use as many full panels as possible.

• If installing low-voltage lighting, wiring must be installed before securing posts to deck

surface.

Step 1 Install posts by attaching the aluminum base to the surface of the deck. Position

the post so the fastener will go into the floor joist, and make sure the decking is firmly

attached to the joist at the location of the posts. If necessary, use wood blocking securely

attached to the joist structure as reinforcement underneath the decking where the posts are

located. Fasteners that hold the post base to the surface should be able to secure to joist or

reinforcement braces, not just the decking itself. Note: When installing aluminum post on top

of a wood surface, screws must be lagged into at least 3" of solid wood (not including the

decking). 5/4" or 1 1⁄2" deck boards do not provide sufficient material for a safe installation. If

necessary, add additional material to the underside of the surface (fig. 2).

Step 2 Position the post assembly onto the location where it will be attached to the deck.

Four 11/32" diameter mounting holes are provided on the base. When the final position is

determined, mark the base hole locations. Remove the post assembly and drill 15/64" holes in

the marked locations into the deck and reinforcement.

Step 3 Reposition the post assembly with the leveling plate inserted between the deck

and the post base, and aligned with the predrilled holes. Insert the post fasteners (NOT

INCLUDED), and partially tighten. Using a level, adjust the leveling set screws with a 3/16"

allen wrench until the post is plumb. Fully tighten the post fasteners to secure the base to

the deck structure. Note: Recommended 5/16" x 4" or longer lag screws.

STOP: Make sure post base trim is installed before continuing.

For rail kits: Baluster connectors are attached to bottom and top rail, but should be

fully tightened by hand to railing before being installed. Do not over tighten.

Tools and Items Needed

• Adjustable wrench

or socket wrench for

bolts, etc.

• Safety glasses/

goggles

• Rubber mallet

(15 or 20)

(2 or 3)

Balusters

Rail Supports

Contents

ALX CLASSIC

INSTALLATION INSTRUCTIONS

• Tape measure

• Lag screws

• 3/16" allen wrench

(4 or 6)

(4)

Rail Support

In-line Brackets

Connectors

with Hardware

Post Cap

ALX Classic Rail

39-in

Post

Base

Trim

Leveling Plate

Rail

Support

Rail Support

Connector

fig. 2

In-line Bracket

Baluster

Connector

fig. 1

fig. 3

fig. 4