Airflow Uno hab Manual de instrucciones de instalación y funcionamiento - Página 5

Navegue en línea o descargue pdf Manual de instrucciones de instalación y funcionamiento para Controlador Airflow Uno hab. Airflow Uno hab 16 páginas. Cavity wall decentralised mechanical ventilation with heat recovery unit
También para Airflow Uno hab: Instrucciones (2 páginas), Kit de instalación (16 páginas), Manual de mantenimiento (2 páginas)

Imprimir página
m
DANGER
CHAPTER 2
GENERAL
INSTRUCTIONS
© Airflow - we reserve the right to make changes without prior notice
– Reasonably foreseeable misuse:
Ventilation units Unohab are not suitable for operation under difficult conditions, such as high levels of humidity,
aggressive media, long standstill periods, heavy contamination, excessive loads due to climatic, technical or
electronic influences. The same applies for the mobile use of fans (vehicles, aircraft, ships, etc.). Usage under these
conditions is only possible with release approval from Airflow, as the standard version is not suitable in this case.
– Improper, prohibited use:
Any use other than the intended use is not permitted! The conveying of solid matter or solid matter content > 10μm
in air and liquid is not permitted. Transport media, which affect the materials of the fan, and abrasive media are not
permitted. Use in explosive atmospheres is not permitted!
1.4 Personnel qualification
m DANGER!
The electrical connection and start-up must only be carried out by qualified electricians.
Installation, servicing and maintenance of the fan must only be carried out by qualified electricians.
individual room ventilation units can be used by children over the age of 8 as well as persons with physical,
Unohab
sensory, or mental disabilities or lack of experience and knowledge, if they are supervised or instructed with regard
to the safe use of the unit and they understand the resulting risks. Children must not play with the unit. Cleaning or
user maintenance must not be carried out by unsupervised children.
2.0
Warranty claims – exclusion of liability
All versions of this documentation must be observed, otherwise the warranty shall cease to apply. The same applies
to liability claims against Airflow. The use of accessory parts, which are not recommended or offered by Airflow, is
not permitted. Any possible damages are not covered by the warranty. Changes and modifications to the unit are
not permitted and lead to a loss of conformity, and any warranty and liability shall be excluded in this case.
2.1 Certificates - guidelines
If the product is installed correctly and used to its intended purpose, it conforms to all applicable EU guidelines at its
date of manufacture.
2.2

Shipping

The individual room fan unit is packed ex works in such a way that it is protected against normal transport strain.
Carry out the shipping carefully. It is recommended to leave the fan in the original packaging.
2.3

Receipt

The shipment (Unohab unit, part number: 90000993) must be checked for damage and correctness immediately
upon delivery. If there is any damage, promptly report the damage with the assistance of the transport company.
If complaints are not made within the agreed period, any claims could be lost.
2.4

Storage

When storing for a prolonged time, the following steps are to be taken to avoid damaging influences: Motor protection
by dry, airtight and dust-proof packaging (plastic bag with desiccant and humidity indicators). Vibration-free, water-
tight and constant-temperature storage at a temperature in the range -20 °C to +40 °C.
In case of a storage period of more than three months or motor standstill, maintenance must be carried
out before start-up according to chapter 6. In case of reshipment (above all, over longer distances; e.g. by
sea), it must be checked whether the packaging is suitable for the form and route of transport. Damages due to
improper transportation, storage or putting into operation are not liable for warranty.
2.5

Mode of operation

Unohab is equipped with an EC axial fan, which runs in a cyclical reversing mode. Thus, the supply air modes,
whereby the outside air flows into the building, continuously alternate with extract air modes, whereby the indoor
air is extracted from the building.
2.6

Performance data

The unit type plate gives an indication of the mandatory electrical values; which must be coordinated with the
local supply network. The fan performances shown in 4.1 on page 7 were established on a test stand according to
DIN EN ISO 5801.
2.7

Noise data

Noise data that refers to certain distances apply to free field conditions. With regard to installation, the sound
pressure level can differ significantly from the catalogue data, as it is highly dependent on the installation conditions,
i.e. on the absorption capability of the room and the room size among other factors (e.g. wind load in wind-exposed
locations).
Unohab Unit
5
Installation and Operating Instructions