KitchenAid 9741159 Manual de instrucciones de instalación - Página 3

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Lavavajillas KitchenAid 9741159. KitchenAid 9741159 8 páginas. Undercounter dishwasher

Imprimir página
Electrical
requirements
Electrical
Shock Hazard
l
Electrical
ground
is required
on this appliance.
l
If cold water pipe is
interrupted
by plastic,
non-
metallic
gaskets or other
insulating
materials,
Do Not
use for grounding.
l
Do Not ground to a gas pipe.
l
Do Not modify the power
supply cord plug.
If it does
not fit the outlet, have a
proper outlet installed
by a
qualified
electrician.
l
Do Not have a fuse in the
neutral or grounding
circuit.
A fuse in the neutral or
grounding
circuit
could result
in an electrical
shock.
l
Do Not use an extension
cord
with this appliance.
l
Check with a qualified
electrician
if you are in doubt
as to whether
the appliance
is
properly
grounded.
Failure to follow these
instructions
could result in
serious
injury or death.
l
If codes permit and a separate
grounding
wire is used, it is
recommended
that a qualified
electrician
determine
that the
grounding
path is adequate.
A single phase, 115volt,
60-Hz,
AC-only, 15- or 20-ampere, fused
electrical supply is required. Time-
delay fuse or circuit breaker is
recommended.
It is recommended
that a separate circuit serving only
this appliance be provided.
It is the personal responsibility
and
obligation of the customer to contact
a qualified electrician to assure that
the electrical installation
is adequate
and is in conformance
with the
National Electrical Code,
ANSVNFPA 70-latest edition and
local codes and ordinances.
The dishwasher can be connected
with flexible armored or non-metallic
sheathed copper cable (with
grounding wire).
A conduit connector must be
installed at junction box. Wire sizes
(COPPER WIRE ONLY) must
conform with the rating of the
dishwasher.
Flexible cord connection
Local codes may permit the use of a
U.L.-listed, flexible, three-conductor
cord terminated with a three-prong,
grounding-type
plug. It is
recommended
that cord kit, Part No.
675456, available from your
KitchenAid dealer or parts supplier,
be used. If the cord kit is not
available locally, the flexible cord
used must be a three-conductor,
16-
gauge cord that meets the National
Electrical Code, ANSVNFPA 70-
latest edition and local codes and
ordinances.
The length of the cord
must not exceed six feet. It must be
routed so it does not touch the
dishwasher
motor or the lower
portion of the dishwasher tub. A
grommet (Part No. 302797) must
cover the hole cut in a metal cabinet
for the flexible cord. The flexible cord
must be plugged into a mating three-
prong, grounding-type
wall
receptacle, grounded in accordance
with the National Electrical Code,
ANSVNFPA 70-latest edition and
local ordinances.
Follow instructions
packaged with the flexible cord.
Water
requirements
The hot water line to the dishwasher
must provide between 20-l 20 psi
water pressure. The hot water heater
should be.set to deliver 120°F
(minimum) water temperature to the
dishwasher
(except as noted in your
Use and Care Guide) for best results.
Use l/2" O.D. copper tubing or 3/8"
galvanized
pipe inlet line.
Dishwasher
inlet valve has 3/8"
internal pipe thread.
Drain
requirements
Product
Damage
l
The drain line connection
to
the house plumbing
must be
a minimum
of 20" above the
floor. A lower drain
connection
may result in
siphoning.
l
If the drain is routed to a
connection
point less than
20" above the floor, the drain
line must form a loop 20"
above the floor. See Figure 3,
Page 4.
l
Do Not kink hose and copper
tubing.
Failure to provide either a 20"
minimum
connection
height or
a 20" high loop will result in
improper
drainage
and may
cause product
damage.
The drain hose should be 9/l 6"
minimum I.D. flexible hose or 5/8"
O.D. copper tubing.
A minimum of
22" flexible drain hose or a 12"
length of copper drain line with 12"
length of flexible hose added is
needed.
Flexible hose, resistant to
heat and detergent, can be found at
plumbing, hardware or automotive
supply stores. Do Not use a drain
line or fittings less than l/2" I.D.
If drain line is copper, clamp a 12"
length of 9/16" I.D. flexible, heat-
and detergent-resistant
hose to the
end of the copper drain line to
connect to the dishwasher
valve.
Page 3