IKEA finputsad Manual - Página 6
Navegue en línea o descargue pdf Manual para Lavavajillas IKEA finputsad. IKEA finputsad 33 páginas. Integrated
También para IKEA finputsad: Manual (20 páginas), Manual de instrucciones (36 páginas), Manual (12 páginas), Manual (29 páginas)
Imprimir página
2
ENGLISH
3
Product description
4
5
ENGLISH
1
6
3
Product description
10
5
6
9
7
Service:
8
0000 000 00000
11
9
First Use
3sec
Advice regarding the first time use
11
9
10
Before installation and first usage of the appliance please
read carefully „ SAFETY and WARRANTY" and „ASSEMBLY
INSTRUCTION" guides available in the product literature bag.
7.
Display
Please remember to remove all transport protection parts from
8.
Half Load indicator light
the dishwasher.
9.
Half Load button
11
Filling the salt reservoir
10. Delay button
The use of salt prevents the formation of LIMESCALE on the
11. START/Pause button with indicator light / Tab
dishes andon the machine's functional components.
• It is mandatory that THE SALT RESERVOIR BE NEVER EMPTY.
Control panel
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and should be filled when the
SALT REFILL indicator light
1
1.
On-Off/Reset button with indicator light
2.
Program selection button
3.
Salt refill indicator ligh
4.
Rinse Aid refill indicator ligh
5.
Program number and delay time indicator
Make sure the cap is screwed on tightly, so that no detergent
6.
Tablet indicator light
can get into the container during the wash program (this could
damage the water softener beyond repair).
As soon as this procedure is complete, run a program without
First use
loading.
ADVICE REGARDING THE FIRST TIME USE
Only use salt that has been specifically designed for
dishwashers. If the salt container is not filled, the water
After installation, remove the stoppers from the racks and the
softener and the heating element may be damaged
retaining elastic elements from the upper rack.
as a result of limescale accumulation. Using of Salt is
FILLING THE SALT RESERVOIR
recommended with any type of dishwasher detergent.
The use of salt prevents the formation of LIMESCALE on the
Whenever you need to add salt, it is mandatory to complete
dishes andon the machine's functional components.
the procedure before the beginning of the washing cycle to
• It is important that the salt reservoir be never empty.
avoid corrosion.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
Setting the water hardness
dishwasher (see PRODUCT DESCRIPTION) and should be
To allow the water softener to work in a perfect way, it is
filled when the SALT REFILL indicator light
essential that the water hardness setting is based on the actual
control panel is lit .
water hardness in your house. This information can be obtained
from your local water supplier. The factory sets the default value
for the water hardness.
2.
3.
Upper rack height adjuster
4.
Upper sprayer arm
5.
Lower rack
6.
Cutlery basket
7.
Lower sprayer arm
8.
Filter Assembly
9.
Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
in the control panel is lit.
h
1. Remove the lower rack and unscrew
1. Remove the lower rack and
the reservoir cap (anticlockwise).
unscrew the reservoir cap
2. Position the funnel (see figure) and
(anticlockwise).
fill the salt reservoir right up to its
2
3 4
5
6 7 8
2. Only the first time you do this: fill
edge (approximately 1 kg); it is not
the salt reservoir with water.
unusual for a little water to leak out.
3. Position the funnel (see figure)
3. Only the first time you do this: fill
and fill the salt reservoir right up
the salt reservoir with water.
to its edge (approximately 1 kg);
4. Remove the funnel and wipe any
it is not unusual for a little water to
salt residue away from the opening.
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
in the
To download the full version visit www.ikea.com
1
Upper rack
2
2
Cutlery rack
4
ENGLISH
3
Foldable flaps
4
Upper rack height adjuster
5
Upper sprayer arm
Make sure the cap is screwed on tightly, so that no detergent can
6
Lower rack
7
get into the container during the wash program (this could damage
1
ENGLISH
7
Lower sprayer arm
the water softener beyond repair).
8
8
Filter Assembly
As soon as this procedure is complete, run a program without
9
loading. The "Pre-Wash" program alone is NOT
Salt reservoir
2
Residual saline solution or grains of salt can lead to corrosion,
10
Detergent and Rinse Aid dispensers
Make sure the cap is screwed on tightly, so that no detergent can
irreparably damaging the stainless steel components.
10
get into the container during the wash program (this could damage
11
Control pannel
The guarantee is not applicable if faults are caused by such
the water softener beyond repair).
circumstances.
As soon as this procedure is complete, run a program without
loading. The "Pre-Wash" program alone is NOT
3
Residual saline solution or grains of salt can lead to corrosion,
heating element may be damaged as a result.
irreparably damaging the stainless steel components.
Whenever you need to add salt, it is mandatory to complete
The guarantee is not applicable if faults are caused by such
4
the procedure before the beginning of the washing cycle.
circumstances.
SETTING THE WATER HARDNESS
5
To allow the water softener to work in a perfect way, it is essential
heating element may be damaged as a result.
that the water hardness setting is based on the actual water hard-
Whenever you need to add salt, it is mandatory to complete
6
ness in your house. This information can be obtained from your local
the procedure before the beginning of the washing cycle.
water supplier. The factory setting is for average (3) water hardness.
• Switch on the appliance by pressing the ON/OFF button.
SETTING THE WATER HARDNESS
• Switch on the appliance by pressing the ON/OFF button.
10
• Switch off the appliance by pressing the ON/OFF button.
To allow the water softener to work in a perfect way, it is essential
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button
that the water hardness setting is based on the actual water hard-
• Hold down button
• Switch on the appliance by pressing quickly the ON/OFF
ness in your house. This information can be obtained from your local
• Switch on the appliance by pressing the ON/OFF button.
water supplier. The factory setting is for average (3) water hardness.
button.
•
The current selection level number and the salt indicator light
• The current selection level number and the salt indicator light
• Switch on the appliance by pressing the ON/OFF button.
•
Press button
both flash
• Switch off the appliance by pressing the ON/OFF button.
WATER HARDNESS TABLE).
• Press button
• Hold down button
WATER HARDNESS TABLE).
• Switch on the appliance by pressing the ON/OFF button.
•
The current selection level number and the salt indicator light
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
•
Press button
1
WATER HARDNESS TABLE).
Water Hardness Table
2
3
Level
Level
4
5
1
3sec
2
Medium
1
• Switch off the appliance by pressing the ON/OFF button.
3
Average
9
10
11
Setting is complete!
2
Medium
4
FILLING THE RINSE AID DISPENSER
5
Very hard
3
7.
Display
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
8.
Half Load indicator light
should be filled when the RINSE AID REFILL indicator light
• Switch off the appliance by pressing the ON/OFF button.
4
9.
Half Load button
in the control panel is lit.
Setting is complete!
5
Very hard
10. Delay button
FILLING THE RINSE AID DISPENSER
11. START/Pause button with indicator light / Tab
Water Softening System
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
Water softener automatically reduces water hardness, conse
should be filled when the RINSE AID REFILL indicator light
quently preventing scale buildup on heater, contributing also to
in the control panel is lit.
better cleaning efficiency.
This system regenerates itself with salt, therefore it is required
to refill salt container when empty.
Frequency of regeneration depends on water hardness level
1. Open the dispenser B by pressing and pulling up the tab on
setting regeneration takes place once per 5 Eco cycles with
the lid.
water hardness level set to 3.
2. Carefully introduce the rinse aid as far as the maximum
Regeneration process starts in final rinse and finishes in drying
(110 ml) reference notch of the filling space - avoid spilling it.
phase, before cycle ends.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
* Single regeneration consumes: ~3.5 L of water;
1. Open the dispenser B by pressing and pulling up the tab on
NEVER pour the rinse aid directly into the tub.
the lid.
* Takes up to 5 additional minutes for the cycle;
2. Carefully introduce the rinse aid as far as the maximum
* Consumes below 0.005 kWh of energy.
(110 ml) reference notch of the filling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
1.
Upper rack
2.
3.
Upper rack height adjuster
4.
Upper sprayer arm
5.
Lower rack
6.
Cutlery basket
7.
Lower sprayer arm
8.
Filter Assembly
9.
Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
for 5 seconds, until you hear a beep.
for 5 seconds, until you hear a beep.
to select the desired hardness level (see
to select the desired hardness level (see
for 5 seconds, until you hear a beep.
Water Hardness Table
°dH
Level
German degrees
to select the desired hardness level (see
Soft
0 - 6
Medium
7 - 11
Water Hardness Table
Average
12 - 17
°dH
°dH
Hard
18 - 34
German
German degrees
Very hard
degrees
35 - 50
Soft
0 - 6
7 - 11
Soft
0 - 6
12 - 17
7 - 11
Hard
18 - 34
35 - 50
Average
12 - 16
Hard
17 - 34
35 - 50
B
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
B
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
opening.
6
7
ADJUSTING T
If you are not com
adjust the quanti
• Switch the dis
• Switch it off u
• Press button
ADJUSTING THE D
• Switch it on u
If you are not complete
•
The current sel
adjust the quantity of ri
•
Press button
• Switch the dishwash
s.
supplied.
• Switch it off using th
• Switch it off u
• Press button
Setting is comple
• Switch it on using th
If the rinse aid le
•
The current selection
supplied. The LO
•
Press button
run out of rinse a
s.
supplied.
the dishwasher m
• Switch it off using th
please follow ins
Setting is complete!
• If you see blui
If the rinse aid level is
• If there are dr
supplied. The LOW RIN
set a high num
run out of rinse aid. A m
the dishwasher model.
please follow instruction
FILLING THE
• If you see bluish stre
• If there are drops of
dishwashers.
set a high number (3
To achieve the b
useof detergent,
We recommend
FILLING THE DETE
or chlorine, as th
Good washing re
dishwashers.
detergent being
°fH
To achieve the best wa
French degrees
Exceeding the st
useof detergent, rinse
wash and increa
0 - 10
We recommend using
The amount can
or chlorine, as these pr
11 - 20
normally soiled i
Good washing results
21 - 30
detergent) or 35m
°fH
°Clark
detergent being used.
°fH
detergent directl
31 - 60
French
English
French degrees
Exceeding the stated a
will be enough.
degrees
61 - 90
degrees
wash and increases en
0 - 10
If the crockery is
The amount can be ad
water before bei
11 - 20
0 - 10
0 - 7
normally soiled items,
of detergent use
21 - 30
detergent) or 35ml (liqu
powder/gel putte
11 - 20
8 - 14
detergent directly insid
31 - 60
will be enough.
61 - 90
21 - 29
15 - 20
If the crockery is only l
water before being pla
30 - 60
21 - 42
of detergent used acco
powder/gel putted insid
B
61 - 90
43 - 62
A
B
A
1.
When measu
A
lier informatio
B there are in
2.
Remove dete
and close the
3. Close the lid
1.
When measuring ou
A
the closing de
lier information to a
B there are indicatio
The detergent d
2.
Remove detergent
according to the
and close the cover
recommend usin
3. Close the lid of the
program so that
the closing device i
achieved.
The detergent dispens
according to the progr
recommend using the
program so that the be
achieved.
thre
to s