ALIBI ALI-CD1080PI Manual de instalación rápida - Página 3

Navegue en línea o descargue pdf Manual de instalación rápida para Cámara de seguridad ALIBI ALI-CD1080PI. ALIBI ALI-CD1080PI 4 páginas. Hd-tvi outdoor infrared bullet camera

Imprimir página

The PTZ control panel direction buttons and the Iris + and Iris - keys are used to navigate the

NOTE

OSD menu and set configuration options in the camera.

OSD menu navigation

For the ALIBI HVR: Navigation and settings in the OSD are made through direction keys and the Iris +

and Iris - buttons in the ALIBI HVR PTZ Control panel. See below.

Direction keys

Iris+ Iris–

ALIBI HVR PTZ Control panel

For remote access to the ALIBI HVR: Navigation and settings in the OSD are made through direction

keys and the Iris + and Iris - buttons in the ALIBI HVR PTZ control panel. See above.

The function of the directional keys and Iris buttons are defined in the table below.

Keys

Function

Move up in the parameter list

Move down in the parameter list.

Move to previous page, field, or move the camera left.

Move to next page, field, or move field right.

Iris+ (OPEN)

Set parameter value, or open sub-menu

Iris– (CLOSE)

Cancel change of parameter.

OSD Definitions

AE: Set automatic exposure mode.

AGC (Automatic Gain Control): Higher gain increases brightness but also increases any noise. When a high

gain level is applied, higher noise levels are seen.

AWB (Automatic White Balance): The function to search for the color which is matched well with the

ambient environment.

BLC (Back Light Compensation): This feature enables the camera to compensate for strong back light

conditions in a selected area of the image.

DELAY TIME (DAY/NIGHT): This option specifies the switching time from color to B/W and B/W to color.

D TO N, N TO D: This option sets the AGC brightness when switching from day to night and night to day.

www.observint.com

Preset95 Call icon

PTZ control panel

Direction keys

Iris+ Iris–

ALIBI HVR remote access PTZ control panel

FACTORY INIT: Select FACTORY to reset the camera configuration to the factory default values.

FLICKER: Feature used to reduce noise in the image produced by AC current at 60 Hz.

FLIP: This feature provides an image that is reflected vertically.

HLC (High Light Compensation): HLC feature is used to identify and suppress the strong light sources that

usually flare across a scene. It improves the detail of the image that would normally be hidden.

LSC (Lens Shading compensation): This feature brightens the image in shaded areas.

MIROR: This feature provides an image that is reflected horizontally.

MOTION: The MOTION feature allows you to quickly identify areas of the image where motion is detected.

PRIVACY: The PRIVACY feature allows you to block areas of the image from being seen. Use the SX, EX, SY,

and EY parameters to set the right, left, up and down limits of the privacy area.

SAVE/EXIT: Save the current configuration settings and close the OSD. The settings are retained even after

if the camera is powered off, and then on again.

SX, EX, SY, EY: Sets the start and end X boundaries and the start and end Y boundaries of a PRIVACY or

MOTION area.

Step 4.

Use the OSD menu to configure the camera

The abbreviated OSD menu tree is shown below.

MAIN MENU

VIDEO

VIDEO OUT (frame rate)

OUT

DAY/

MODE

NIGHT

AWB

MODE

SPECIAL

PRIVACY

EFFECT

Video settings

SYSTEM

CAM ID

EXIT

SAVE/

EXIT

Examples

The following examples provided demonstrate how to use the menus to perform basic configuration tasks.

For clarity, the background video image was removed in the screens included here.

Example 1: Change video frame rate

The video frame rate parameter can be set using the Main Menu VIDEO OUT submenu. To change the

setting:

Open the OSD Main Menu (see "Step 3. Open the OSD menu" on page 2).

EXT

COLOR

B/W

AUTO

USER

PUSH

Set

Temp (K)

ESC

HOLD

HLC

MOTION

FLIP

MIRROR

ID DISPL

LANGUAGE

FACTORY

NAME DISPL

INIT

EXIT