Makita 5143R Manual de instrucciones - Página 6
Navegue en línea o descargue pdf Manual de instrucciones para Herramienta eléctrica Makita 5143R. Makita 5143R 13 páginas. Circular saw
También para Makita 5143R: Manual de instrucciones (13 páginas), Manual de instrucciones (13 páginas), Manual de instrucciones (12 páginas), Manual de instrucciones (16 páginas), Manual de instrucciones (13 páginas)
Imprimir página
ENGLISH
1 Hex wrench
2 Shaft lock
3 Tighten
4 Loosen
5 Saw blade
6 Outer flange
7 Inner flange
8 Outer flange
9 Hex socket head bolt
0 Saw blade
q Setting protuberances
w Hex socket head bolt
(For adjusting riving knife)
SPECIFICATIONS
Model
Blade diameter .................................................... 165 mm
Max. cutting depth
At 90° ............................................................... 54 mm
At 45° ............................................................... 38 mm
No load speed (RPM) ......................................... 5,000
Overall length ...................................................... 330 mm
Net weight ........................................................... 4.2 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
Safety instructions.
ADDITIONAL SAFETY RULES
1. Wear hearing protection.
2. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use.
Don't use if lower guard does not close briskly
over saw blade.
CAUTION: If saw is dropped, lower guard may
be bent, restricting full return.
3. Do not use blades which are deformed or
cracked.
4. Do not use blades of high speed steel.
5. Do not stop the blades by lateral pressure on
the saw blade.
6. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
7. DANGER: Keep Hands Away From Cutting
Area. Keep hands away from blades. Don't
reach underneath work while blade is rotating.
6
Explanation of general view
e Cutting depth
r Loosen
t Lever
y Thumb nut
u For 45° bevel cuts
i For straight cuts
o Base plate
p 45° angle cuts
a Straight cuts
s Top guide
d Base
f 60° angle cuts
5603R
Don't attempt to remove cut material when
blade is moving.
CAUTION: Blades coast after turn off.
8. Support Large Panels.
Large panels must be supported as shown in
Fig. A to minimize the risk of blade pinching
and kickback.
When cutting operation requires the resting of
the saw on the work piece, the saw shall be
rested on the larger portion and the smaller
piece cut off.
To avoid kickback, do support board or panel
near the cut.
Don't support board or panel away from the cut.
g 45° angle cuts
h 30° angle cuts
j Straight cuts
k Blade
l Base
; Top guide
z Lock-off button
x Switch trigger
c Vacuum cleaner
v Limit mark
b Brush holder cap
n Screwdriver
5703R
5903R
190 mm
235 mm
66 mm
85 mm
46 mm
64 mm
4,800
4,500
356 mm
400 mm
5.2 kg
7.6 kg
5103R
5143R
270 mm
355 mm
100 mm
130 mm
73 mm
90 mm
3,800
2,700
442 mm
607 mm
9.4 kg
14.5 kg
Fig. A
Fig. B