ALIBI ALI-TS4002R Manual de instalación rápida - Página 5
Navegue en línea o descargue pdf Manual de instalación rápida para Cámara de seguridad ALIBI ALI-TS4002R. ALIBI ALI-TS4002R 5 páginas. 2 mp 4-in1 hd 130 ft ir bullet camera
Imprimir página
SHARPNESS: Sharpness determines the amount of detail an imaging system can reproduce. You can set the
SHARPNESS value from 1 to 9.
SATURATION: Adjust this feature to change the color saturation. The value ranges from 1 to 9.
DNR (Digital Noise Reduction): Use DNR function to decrease the noise in the image, especially when
capturing moving images in poor light conditions, to produce a sharper image. You can set the DNR value
from 1 to 9.
MIRROR: This feature is used to reflect the image. MIRROR can be set to OFF, H, V, and HV.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and vertically.
FACTORY DEFAULT
Click Iris+ to enter the submenu, and click OK to reset all the settings to the factory default. Click Cancel
to return to the menu without resetting the camera.
EXIT
Move the cursor to EXIT and click Iris+ to exit the menu without saving.
SAVE & EXIT
Move the cursor to SAVE & EXIT, and click Iris+ to save the settings and exit the menu. If new settings are
not saved, they remain in effect only until the camera is powered off or reset.
Specifications
C amera
Image Sensor
2MP CMOS image sensor
Signal System
PAL / NTSC
Effective Pixels
1920 (H) × 1080 (V)
Min. illumination
0.01 Lux @ (F1.2, AGC ON), 0 Lux with IR
Shutter Time
1/25 (1/30) s ~ 1/50,000 s
2.8 ~ 12 mm @ F1.4
Lens
Angle of view: 102.25° ~ 32°
Lens Mount
Φ14
Day & Night
ICR
Angle Adjustment
Pan: 0° to 360°, Tilt: 0° to 90°, Rotation: 0° to 360°
Synchronization
Internal synchronization
Video Frame Rate
1080p @ 25 fps / 1080p @ 30 fps
HD Video Output
1 analog HD output
S/N Ratio
> 62 dB
General
Operating Conditions
-40 °F ~ 140 °F (-40 °C ~ 60 °C), Humidity 90% or less (non-condensation)
Power Supply
12 Vdc ± 15%
Power Consumption
Max. 4 W
Protection Level
IP66
IR Range
Up to 130 ft (40 m)
Dimensions
3.62" × 3.34" × 3.34" (92 mm × 84.8 mm × 269.6 mm)
Weight
Approx. 1.98 lb (900 g)
www.observint.com
5
Cleaning
Clean the camera with an approved glass cleaning solution and a lint free cloth.
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
•
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
•
These may cause damage to the surface over time.
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
CAUTION
carefully follow the accompanying instructions.
Troubleshooting
Problem
Possible Cause
Nothing appears on the screen
- Check the power connection.
- Check the video signal cable connection to the monitor.
- Check camera settings to verify the video resolution mode of the
camera and recorder match
The video image is dim or not clear.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark.
- Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω / Hi-Z)
properly, and check the cable connections.
The camera is not working properly and
- Verify that the camera is correctly connected to an appropriate regulated
the surface of the camera is hot.
power source.
The image on the monitor flickers
- Make sure that the camera isn't facing direct sunlight or fluorescent light.
If necessary,change the camera position.
© 2019 Observint Technologies. All rights reserved.