KitchenAid 9750520 REV A Instrucciones de instalación - Página 4

Navegue en línea o descargue pdf Instrucciones de instalación para Gamas KitchenAid 9750520 REV A. KitchenAid 9750520 REV A 5 páginas. 30" electric freestanding range

Imprimir página

Push cable,

located on rear of

range, up and into the two

hooks on the anti-tip

bracket. Check that cable is

secure in both hooks by

pulling cable towards range.

If cable comes out of hooks,

reposition cable to insure that

in both anti-tip bracket hooks.

final position.

cable fits securely

Slide range into

/17/

If installing the range in a mobile

home, you MUST secure the range to

the floor. Any method of securing the range is

adequate as long as it conforms to the standards

listed in the Mobile Home Installation

Instructions,

Panel A.

Place rack in oven. Place level on

rack, first side to side; then front to

back. If range is not level, adjust the leveling legs

up or down until the range is level.

Note: Oven must be level for satisfactory baking

conditions.

OFF

LO n

each surface unit

control knob to "HI"

position. Check the

operation of the

cooktop elements and indicator lights.

Panel C

120

"88:88" should appear in the clock

disolav. Press the "Clock Set" button.

"TIME, HR AND-MIN will light up in the display.

"0:OO" will appear and the ":" will be flashing.

Press the number buttons for the correct time of

day. Press "Start/Enter"

button to start the clock.

Check the operation of the oven

element. Press the "BAKE" button.

"350"" will appear in the temperature display. The

ON, Bake Element, Outer Broil Element and

Oven Cavity symbols will light up in the display.

Press the "Start/Enter"

button.

The bottom element should glow red and the

indicator light should be on. The upper element

should become hot but not glow red. The oven

indicator light goes off when the oven is

preheated.

Press "Cancel/OFF"

button.

122

. Check the operation of the broil

element. Press the "BROIL" button.

"500"" will appear in the temperature display. The

ON, Inner and Outer Broil Elements and Oven

Cavity symbols will light up in the display. Press

the "Start/Enter"

button.

The top element should glow red and the

indicator light should be on.

Press the "Cancel/OFF"

button.

To get the most efficient use from your

new electric range, read your KitchenAid

Use and Care Guide. Keep Installation

Instructions

and Guide close to the

electric

range

for easy reference.

8.9. IO. 11.15. '6.

18.

Numbers

correspond

to steps.

4-wire electrical connection

Use this wiring method for mobile homes and

whenever 4.wire installation is required.

U.L. llsted

conduit

connecxor

If appliance

is to be connected

directly

to fused disconnect

or circuit

breaker

box: Assemble a U.L.-listed conduit connector in

the conduit connector opening provided. Inset-f the

power supply cable through the conduit connector,

allowing enough slack to easily attach the wiring to

the terminal block.

U.L.-&ted

strain relief

show

----'ClampIng

screws

If a U.L.-listed,

40-ampere

range power supply

cord (pigtail)

is used:

Remove the knockout for the 40.ampere power

supply cord. Assemble a U.L.-listed strain relief in

the hole. Insert the power supply cord through the

strain relief, allowing enough slack to easily attach

the wiring to the terminal block.

Do not loosen the factory installed nuts already

installed on the terminal block.

Remove the grounding-link

screw from

the range frame. Save the grounding

screw. Bend up rhe grounding link so that it does

not contact the range.

Green -

Insulated

wire

l-z-l-

ding

lk.l

. -Connect the green grounding wire to the

range using the grounding screw

removed in Step B. The green grounding wire

must be attached first and must not contact any

other terminal.

Sllver-colored

terminal

block

screw

Green -

Insulated

wlre

- U.L. llsted strain

relief shown.

. Connect the neutral (white) wire to the

center, silver-colored

terminal screw on

the terminal block. Connect the other two wires to

the outer terminals on the terminal block. Use ring-

type terminals only. Connect and securely tighten

the brass nuts that are provided on a plastic strip

attached to the range. Do Not loosen the factor-y

installed nuts already on the terminal.

Be sure that the nuts are installed tight.

(El

Tighten the strain relief clamping screws

or the locking ring and clamping screws

of the conduit connector. Replace the terminal

block cover.

Continue installation at Step 12, Panel B.