KitchenAid 9752913 Instrucciones de instalación - Página 3

Navegue en línea o descargue pdf Instrucciones de instalación para Gamas KitchenAid 9752913. KitchenAid 9752913 5 páginas. 30"

Imprimir página
Now start...
With range in kitchen.
1
I Put on safety glasses and gloves. Remove
shipping materials, tape and protective film from
range. Keep cardboard bottom and shipping base
under range. Remove oven racks and parts
package from inside oven.
2
I Take 4 cardboard corners from the carton.
If codes permit and a separate ground wire is used,
it is recommended that a qualified electrician
determine that the ground path and wire gauge are
in accordance with local codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not sure
range is properly grounded.
Do Not have a fuse in the neutral or ground circuit.
A
If connecting
to a four-
v&z electrical
system...
Do Not connect
the cabinet-ground
conductor
to the white
(neutral)
junction
box
wire.
cable from
junction
power
supply
I
white
w
wires
%
black
Stack one
cardboard corner
on top of another.
Repeat with the
other two corners.
Place corners
lengthwise on the
floor in back of
range so corners
will support outer
side edges of range
as shown.
A
I A four-wire or three-wire, single-phase,
120/240-volt, 60-Hz; 50-amp, AC-only, electrical
supply (or four-wire or three-wire 120/208-volt if
specified on the model/serial rating plate) is
required on a separate 50-ampere circuit, fused on
both sides of the line. A time-delay fuse or circuit
breaker is recommended. The model/serial rating
plate is located on the oven frame behind the
storage drawer panel.
B
. THE RANGE MUST BE CONNECTED WITH
COPPER WIRE ONLY.
wires
/
\
\/
spacers
bcardboard
corners
1 b ar&
m
U.L.-listed
Figure
green
t-H
conduit
wires
cable from
connector
range
1. Disconnect the power supply.
2. Separate the green (or bare) and white
appliance cable wires.
3. Connect the white range cable wire to the white
(neutral) wire in the junction box.
4. Connect the two black wires together with twist-
on connector.
5. Connect the two red wires together with twist-
on connector.
6. Connect the green range wire to green ground
wire in junction box.
7. Replace junction box cover.
B.
Where local codes permit...
connecting
the cabinet-ground
conductor
to
the white
(neutral)
junction
box wire:
cable from
junction
power
supply
box,
I
I
black
C
I Wire sizes and connections must conform to
the requirements of the National Electrical Code,
ANSI/NFPA 70 - latest edition (*See Panel A) and
all local codes and ordinances for the kilowatt rating
of the range.
Excessive weight Hazard
Use two or more people to move and install
range.
1
Failure to do so can result in back or other injury.
D
I This range should be connected directly to
the fused disconnect or circuit breaker box through
flexible, armored or non-metallic sheathed, copper
cable (with ground wire). Locate the junction box
to allow two to three feet of slack in the line so
that the range can be moved if servicing is ever
necessary. Do Not cut the conduit.
A U.L.-listed conduit connector must be provided
at each end of the power supply cable (at the
range and at the junction box).
3
I Firmly grasp the range and gently lay it on
its back on the cardboard corners.
4
I Pull cardboard bottom and shipping base
firmly to remove from range.
E
I The wiring diagram is located on the back of
the range or on the inside of the storage drawer in a
clear plastic bag.
5
I Use an adiustable wrench to loosen the
green
wire
Figure 2
L
cable from
connector
range
leveling legs l-l;2 turns.
6
I Place cardboard or hardboard in front of
Grounded
Neutral
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect together 3 wires: green and white
range cable wires and the white (neutral) wire in
junction box.
4. Connect the two black wires together with twist-
on connector.
5. Connect the two red wires together with twist-
on connector.
6. Replace junction box cover.
C
Where local codes Do Not
pe;mit...
connecting
the cabinet-ground
conductor
to
the white
(neutral)
junction
box wire:
range. Stand range back up onto cardboard or
hardboard.
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use B-gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions
can result in
death, fire, or electrical shock.
Tip Over Hazard
A child or adult can tip the range and be
killed.
Connect
anti-tip
bracket to rear range foot.
Reconnect
the anti-tip
bracket, if the range
is moved.
Failure to follow
these instructions
can
result in death or serious
burns to children
and adults.
junction
cable from
power
supply
white
This range is manufactured
with white (neutral)
power supply wire and a cabinet-connected
bare
ground wire twisted together.
Remove junction box cover.
Connect the range cable to the junction box
through a U.L.-listed conduit connector.
Complete electrical connection
according to local
codes and ordinances.
7
n
Place the anti-tip
bracket template on the
floor in the cabinet
opening so that the left
edge is against cabinets
and the top edge is
against the rear wall,
molding or cabinet.
25" (63.5 cm)
countertop
over
Figure 3
cable from
conduit
range
connector
Grounded
Neutral
1. Disconnect power supply.
2. Separate the green and white appliance cable
wires.
3. Connect the white range cable wire to the white
(neutral) wire in the junction box.
4. Connect the two black wires together with twist-
on connector.
5. Connect the two red wires together with twist-
on connector.
6. Connect the green or bare ground wire from the
range cable to a ground wire in the junction
box.
7. Replace junction box cover.
j/L-;:
template
Panel B