Makita BMR100 Manual de instrucciones - Página 9

Navegue en línea o descargue pdf Manual de instrucciones para Herramienta eléctrica Makita BMR100. Makita BMR100 20 páginas. Makita bmr100: specifications
También para Makita BMR100: Desglose de piezas (3 páginas), Manual de instrucciones (9 páginas)

Imprimir página

Note:

A stereo symbol will appear on the display, if the

station found is a stereo station.

Note:

The radio will continue to search next available

stations if you do not press Scan button again when it

finds a radio station.

4. Rotate the Volume control to get required sound level.

LCD display will show sound level changes.

Note:

During operating volume control, you can press in

Tuning/Volume control knob to change volume control

to tuning control status.

5. To turn off the radio, press the Power button. Display

will show OFF.

Manual Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Adjust the antenna as described above.

3. A single rotary to the Tuning control will change the

frequency in the following increment:

FM: 50 or 100 kHz

AM (MW): 9 or 10 kHz

Note:

If the radio is in volume control status, press in the

tuning/volume control to become Tuning status.

4. Keep on rotating the Tuning control until the required

frequency shown on the display.

5. Rotate the volume control to get required sound level.

6. To turn off the radio, press the Power button. Display

will show OFF.

Storing stations in preset memories

There are 5 memory presets for each waveband.

1. Press the Power button to turn on the radio.

2. Tune to required station using one of the methods

previously described.

3. Press and hold down the required preset until radio

beeps. The preset number will appear in the display

and the station will be stored under chosen preset

button.

4. Repeat this procedure for the remaining presets.

5. Stations stored in preset memories can be overwritten

by following above procedures.

Recall stations from preset memories

1. Press the power button to turn on the radio.

2. Select the required waveband.

3. Momentarily press the required Preset button, the

preset number and station frequency will appear in the

display.

Setting the radio alarm

When the radio alarm is selected, the radio will turn on

and play the chosen radio station at the chosen alarm

time. The radio alarm will continue for one hour unless

turned off by pressing the Power button. Pressing the

Power button whilst the alarm is activated will cancel the

alarm for 24 hours.

Note:

When the radio is in low battery status, the radio alarm

can't be activated.

a. Setting radio alarm time:

1. The radio alarm can be set either when radio is on or

off.

2. Press and release radio alarm button

radio alarm symbol will flash.

3. During radio alarm symbol flashing, press

for more than 2 seconds followed by a beep.

4. Display Hour will flash, rotate Tuning Control to select

the hour then press

setting.

5. Follow same procedures of setting hour to set

required minute. Press

time setting.

b. Setting radio alarmed station

1. During setting radio alarm time and radio alarm

symbol is flashing, press Band button to activate the

radio to select required wake-up band and station by

manual tuning and recall the preset stations. Press

button to complete radio alarm setting.

Display will show

2. When above radio alarm time and station are set,

press and hold down radio alarm button

2 seconds followed by a beep to switch alarm on or

off. Display will show

Note:

If new radio alarm station is not selected, it will select

the last alarm station.

Setting the HWS (Humane Wake

System) buzzer alarm

A beep tone will activate when selecting the HWS buzzer

alarm.

The alarm beep will become shoter and shoter every

15 seconds for one minute followed by one minute silence

before repeating the cycle.

The HWS alarm will sound for one hour until turning off by

pressing the Power button. Press the Power button whilst

the alarm is activated will cancel the alarm for 24 hours.

1. The HWS buzzer alarm can be set either radio is on or

off.

2. Press and release the HWS buzzer alarm button

, the symbol will flash.

3. During the symbol flashes, long pressing the

button for more than 2 seconds followed by a beep

and display Hour digit will flash.

4. Rotate Tuning Control to select required alarm hour,

then press time set button

digit will then flash.

5. Rotate Tuning Control to select required alarm minute,

the press time set button

buzzer alarm setting.

, the

button

button again to confirm hour

button to complete alarm

when radio alarm is set.

again. The minute

again to complete HWS

for