ALIBI ALI-NS1132VR Manual de instalación rápida - Página 2
Navegue en línea o descargue pdf Manual de instalación rápida para Cámara digital ALIBI ALI-NS1132VR. ALIBI ALI-NS1132VR 7 páginas. 2mp ip dome camera
Imprimir página
3.
Remove the black liner and set aside.
microSD card slot
4.
Push the microSD card into the slot until it is fully seated, and then release it. When installed
properly, it will slide into the slot smoothly, and be held in place after release.
Step 2.
Install the camera
For outdoor installations, refer to "TVS 2000V lightning protection, surge protection and voltage transient
protection" on page 7 for additional installation considerations.
The camera includes hardware to install it directly to a mounting surface. Camera drop cables can be
routed through the conduit port on the side of the lower dome, through the mounting surface. To install
the camera:
1.
If the dome assembly is not already removed, use the L-wrench provided to fully loosen the dome
captive screws, and then lift the dome assembly off the camera. The dome assembly is connected
to the camera with a safety cable. Set the dome assembly to the side, being carefully to not scratch
the clear plastic.
2.
Determine the best fasteners
for securing the camera
to mounting surface. The
mounting hardware provided is
suitable for many surface types.
3.
Using the Drill Template
provided, mark the location of
the mounting screw holes. If
the drop cable will be routed
through the mounting surface,
mark the location of the hole for
the camera drop cables.
4.
Drill holes for the mounting
fasteners, and for the drop cable
where needed.
Connect camera drop cables to LAN and power cables
This camera features Power over Ethernet (PoE) powering. When PoE is used, a power extension cable is
not needed.
5.
Route LAN and power (if needed) extension cables.
6.
Connect the network LAN and power extension cables to the camera drop cables:
a.
Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from
moisture and other contamination, if necessary. A Weatherproof Ethernet Fitting is provided.
Installation instructions for the fitting are included later in this document.
www.observint.com
2
Reset button"
Mounting
screw hole
Wall insert
Drop
cables
Lower
dome
assembly
Mounting
screws
12 Vdc power connector with protective plug
Ethernet connector -
PoE capable
Network drop cable
from camera
Weatherproof Ethernet Fitting installed
Failure of the power or Ethernet connector due to moisture or another contaminant
!
is considered an installation error, which voids the warranty. If installing this
camera in a location such as an overhang, shop, garage, kitchen, etc. where high
WARNING
humidity or dust is present, seal these connections adequately.
If the camera will be powered using PoE, ensure that the plug in the 12 Vdc drop cable is securely
in place to prevent contamination.
CAUTION
If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc
b.
power cable to the camera drop cable. The polarity of the drop cable connector is shown in
the drop cable photo above.
Before applying power to the camera through the 12 Vdc drop cable, ensure that the polarity is
correct. An incorrect connection may cause a malfunction and can damage the camera.
CAUTION
Do not apply power to the camera at this time. Before applying power to the camera, ensure that
the polarity is correct. An incorrect connection may cause a malfunction and can damage the
CAUTION
camera.
7.
For outdoor installations, seal holes drilled in the mounting surface to block moisture and other
contaminants, if necessary.
8.
Secure the camera to the mounting surface using appropriate screws.
9.
Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.
Step 3.
Install the Alibi Config Tool software
NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.
The Alibi Config Tool is a PC-based network utility for discovery of Alibi compatible devices. It provides
an easy way to activate devices, configure camera and recorder network configuration settings, and set
device passwords. It can be installed on a Microsoft® Windows® operating system that has direct access
to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool from
AlibiSecurity.com/Resources.
1.
Download the Alibi Config Tool from the AlibiSecurity.com/Resources website. At the time when
this document was published, the file is named: alibi-config-tool.zip and is about 80MB.
2.
Un-zip the file on a computer with Microsoft Windows (Windows 7 or newer) that is connected to
the LAN where your Alibi camera is connected.
Run the file contained in the zip file: Alibi Config Tool.exe. Follow the on-screen instructions to
3.
install the file.
4.
Open the Alibi Config Tool application. When the application opens, it automatically "discovers" and
lists all Alibi compatible devices on the LAN. See below.
Note: In the screen above, the tool can discover devices on other subnets. It will also list other Alibi
compatible devices on the LAN, and devices with the address 192.168.1.64 (an inactive Alibi device).
Network cable from
router or switch
© 2019 Observint Technologies. All rights reserved.