KitchenAid KGRT607HBS9 Manual de instrucciones de instalación - Página 7
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Gamas KitchenAid KGRT607HBS9. KitchenAid KGRT607HBS9 12 páginas. 30" freestanding sealed burner gas range with self-cleaning thermal/convection oven
Imprimir página
Slide@ ranges:
countertop
preparations
The cooktop
sides
of the slideqn
range
fit
over
the cutout
edge
of your
countertop.
[f you
have
a square
finish
(flatt
countertop
and the opening
width
is 30""
(76.2 cm),
no countertop
preparation
is
required.
Formed
front-edged
countertops:
Must
have
molded
edge
shaved
fiat
1/2"" (1.3 cm) from
each front
corner
of opening.
cm)
30-7/8" (78.4 cm)
J
,_
Formed or tiled
countertop trimmed
1/2" (1.3 cm) back at
front corners of
countertop opening.
22-5/8"
(57,5 cm>
Cooktop
sides of
"f
I_
range fit over edges
of
[
countertop
opening.
[
Tile countertops
may
need
trim
cut back
1/2"" (1.3 cm) from
each front
corner
and/or
rounded
edge
flattened.
[f countertop
opening
width
is greater
than
30"" (76.2 cm),
adjust
the
1/2""
(1.3 cm) dimension.
Countertop
must
be level.
Place
level
on
countertop,
first
side to side; then
front
to back. if countertop
is not level,
range
will
not be level.
Oven
must
be level
for
satisfactory
baking
conditions.
New start...
Excessive
Weight
Hazard
Use two
or more
people
to move
and
instal[
range.
Failure
to do so can result
in back or
other
injury.
1[]
Remove
shipping
materials,
tape
and protective
film
from
range.
Keep
cardboard
bottom
and shipping
base
under
range.
Remove
oven
racks and
parts
package
from
inside
oven.
NOTE:
[f you
are installing
a slide-in
range,
remove
back vent
package
from
range
top. See step
6 for vent
installation.
m Take four
ca rd boa rd
---__
corners
from
the
carton.
Stack
one
cardboard
corner
on top
of another.
Repeat
with
other
two
corners.
Place them
lengthwise
on the
floor
behind
the range--to
support
the
range
when
it is laid on its back,
Firmly
grasp
the range
and gently
lay it on its
back on the cardboard
corners.
z Puii cardboard
shipping
base
firmly to remove.
M Use an adjustable
wrench to
loosen the leveling
legs 1-1/2 turns.
M Piace
cardboard
or hardboard
in
front
of range.
Stand
range
back up onto
cardboard
or hardboar&
Rear vent
installation
(slideqn
ranges
only):
Remove
the outside
screws
from
rear trim
on range.
Use screws
to
attach
rear vent
to range.
Rear vent must
be installed,
7_
Check
that the type
of gas supply
is
correct
for this
range.
(See model/serial
rating
plate.)
If connecting
to LR gas,
follow
directions
in Conversion
Kit
included
in your
literature
package.
If connecting
to Natural
gas, continue
with
anti4ip
bracket
installation.
Anti-tip
bracket
installation
Tip Over
Hazard
A child
or adult
can tip the range
and
be killed.
Connect
anti-tip
bracket
to rear
range
foot.
Reconnect
the anti-tip
bracket,
if the
range
is moved.
Failure
to follow
these
instructions
can
result
in death
or serious
burns
to
chi[dren
and adults.
Contact
a qualified
floor
covering
installer
for the best
procedure
for
drilling
mounting
holes
through
your
type
floor
covering.
be necessary
to anchor
the bracket
to the
sub-floor.
Longer
screws
are available
from
your
local
hardware
store.