Garden Oasis FD0133BA Manual del usuario - Página 3

Navegue en línea o descargue pdf Manual del usuario para Fuente al aire libre Garden Oasis FD0133BA. Garden Oasis FD0133BA 3 páginas. Lion wall fountain

Imprimir página

noticeable decrease in performance is detected. Failure to clean the pump will result in overheating of the pump. .

7. Before cleaning, always disconnect the pump from the power source.

8. Disassemble the pump by removing the filter and regulator/impeller plate. Remove the impeller/rotor assembly by gently pulling on the impeller blades. Use

a soft cloth or brush to clean the area inside of the pump housing. Clean the filter, gland and impeller in warm soapy water. Reassemble the pump and

inspect for proper operation. Please see the diagram which matches your pump below:

9. Although it is not required, pumps generally last longer if left running continuously as it reduces the wear from starting and stopping. However, running the

pump continuously will also use a little more electricity, and will require you to refill the fountain more frequently. If mosquitoes are a problem in your area, it

is recommended to run the fountain as much as possible to prevent standing water, where mosquitoes breed. You may also add a few drops of

anti-mosquito water treatment, available at your local home and garden store, to the fountain water

10. Place the fountain in a location that will not be damaged should the area come in contact with liquids.

11. To eliminate water damage to floors and/or surrounding fountain areas, check for leaks and excessive splashing after initial installation and on a regular

basis.

12. If your fountain develops a leak and a visible crack is detected, plastic epoxy or Clear Silicone II sealant may be used to seal it. If the fountain leaks without

a visible crack, turn the pump off, fill the fountain and let the fountain sit for one week. If there is a crack, it will appear white. Remember to keep the water ¾

full as will evaporate over time. Seal the leak with plastic epoxy or Clear Silicone II sealant.

13. If the fountain is not in use for an extended period of time, disconnect the power and empty all the water from the fountain. Do not tip the fountain to empty

the water. Use a siphon pump or a small bucket.

14. The fountain should not be operated in temperatures below 41° Fahrenheit / 5° Celsius to prevent frost damage. During winter months, before the

temperature hits freezing, disconnect the power, drain your fountain and store it in a heated area. If the fountain is stored outdoors in freezing temperature,

disconnect the power, empty all the water from the fountain, remove the pump and any lights if possible, make sure it is completely dry and cover it with a

tarpaulin. Any water left in the fountain may freeze and expand causing the fountain to crack. .

15. If your fountain is equipped with an independent light set, you can use an outlet timer to have the lights activate during night time hours. Please note, on

some models the lights cannot be operated independently from the pump so the lights are on, when the pump is on.

If the pump does not operate...

1. Check to make sure the pump is connected to a power source.

2. Check the water level to ensure the pump is completely submerged. Add water as needed.

If the pump operates, but, there is no water flow...

1. Check the water level to ensure the pump is completely submerged. Add water as needed.

2. Check the supply tube for any kinks or folds and correct.

If the pump operates, but there is no water flow and the pump is fully submerged and the supply tubing has no kinks...

1. Disconnect the pump from the power source.

2. Disconnect the supply tube from the pump outlet.

3. Check for clogs or holes and clean the tubing inside and outside if necessary.

4. Check for clogs and clean the pump inlets and outlet if necessary.

5. Place the pump back into the water outlet side up and then re-connect the pump to the power source.

6. Once the water begins to flow from the pump, re-connect the supply tubing to the pump outlet.

7. Check for any air trapped in the water supply tube which may prevent the pump from working.

If the pump runs with low or high water circulation...

1. Check and adjust the regulator dial or slide on the front of the pump. Adjust the dial/slide towards (+) to increase water flow or towards (-) to decrease

water flow.

If the pump operates, but the water flow is uneven or non existent and the pump makes noise...

1. Check the impeller assembly for wear. Remove the front cover and regulator/impeller plate and remove the impeller assembly. Clean the impeller

assembly and inspect for wear. If the rotor spins freely from the magnetic body, the impeller assembly is worn and needs to be replaced. Contact customer

service for replacement parts.

If the pump starts to make noise...

1. Check the water level to ensure the pump is completely submerged. If the water level drops below the pump intake, it may suck in air and cause the noise

or the pump to completely stop working.

2. Move the pump away from the sides of the basin or place a piece of foam or sponge underneath the pump to isolate any vibration which causes the noise.

If the water starts to foam...

1. Check the water level to ensure the pump is completely submerged. If the water level drops below the pump intake, it may suck in air and cause the pump

to 'spit' and foam the water.

2. Add a few drops of anti-foaming water treatment, available at your local home and garden store, to the fountain water.

If the water flow is uneven...

1. Gently sweep across the water surface to achieve even water flow across the face of the fountain.

2. Check the top of the basin to ensure it is level. If not, shim the basin from the bottom until the top spillway is level or has achieved even water flow all

around.

SAVE

SAVE THESE

THESE

THESE IN IN IN INS S S S TRUCTIONS!

THESE

TRUCTIONS!

TRUCTIONS! This

TRUCTIONS!

Each Silk Road Gifts product may have variations in texture, finish and appearance from one unit to the next. This enhances the beauty of the product and

makes your Silk Road Gifts product uniquely individual. Some products and finishes are intentionally weathered or worn in appearance for aesthetic design.

Printed in in in in China

Printed

China

TROUBLESHOOTING

TROUBLESHOOTING GUIDE

TROUBLESHOOTING

This manual

This

manual contains

manual

contains

contains important

important

important safety

important

GUIDE

safety and

safety

and operating

and

operating

operating instructions

operating

instructions for

instructions

appliances.

for outdoor

for

outdoor use

outdoor

use

use electrical

use

electrical

appliances.