Jandy CPLVLEDP100 Manual de instalación - Página 11
Navegue en línea o descargue pdf Manual de instalación para Equipos de iluminación Jandy CPLVLEDP100. Jandy CPLVLEDP100 20 páginas. Watercolors led lights underwater large and small light
También para Jandy CPLVLEDP100: Manual de instalación (16 páginas)
6.2
To Reset to the Beginning of the
Color Sequence
Turn the light OFF, wait four (4) to fi ve (5) seconds,
then turn ON, the light will return to the beginning of
the color cycle (Alpine White).
NOTE If an AquaLink RS control system is being used
the color set can be selected using the indoor
controller.
NOTE To synchronize colors on multiple Jandy
WaterColors Light systems wired to separate
switches, perform the above actions on
all of their switches simultaneously. All
Jandy WaterColors Lights will synchronize
automatically if activated by the same switch.
No other accessories are required.
Section 7. Replacing Light Engine
(PCB)
WARNING
Always disconnect power to the color light at the
circuit breaker before servicing the light. Failure to do
so could result in death or serious injury to installer,
serviceman, pool or spa users or others due to
electrical shock.
1.
Turn off the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2.
Be sure to have the following items:
•
A new lens gasket, P/N R0451101 for the large
light or P/N R0400501 for the small light.
•
A light engine. See Table 2 for specifi cation.
WARNING
Replace light engine with the same type. Failure
to replace the light engine with the same type will
damage the light assembly and may cause an
electrical hazard resulting in death or serious injury
to pool or spa users, installers, or others due to
electrical shock, and may also cause damage to
property. Be sure the power is switched OFF before
removing or installing PCB. Allow PCB to cool before
replacing.
3.
To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove light
assembly from niche and gently place assembly
on the deck. It is not necessary to drain down the
pool. See Figure 6.
Table 2.
Light Specifi cations
Model
Fixture
Voltage
Jandy WaterColors
12 Volt AC
Large Light
Jandy WaterColors
120 Volt AC
Large Light
Jandy WaterColors
12 Volt AC
Small Light
Jandy WaterColors
120 Volt AC
Small Light
WARNING
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock.
4.
Pool Clamp Removal.
a. Loosen the Phillips head screws (six (6) for small
a. Loosen the Phillips head screws (six (6) for small
light, eight (8) for large light) to allow the bottom
light, eight (8) for large light) to allow the bottom
clamp to be removed from the face ring assembly.
clamp to be removed from the face ring assembly.
Do not remove the screws or the retaining rings.
Do not remove the screws or the retaining rings.
The retaining rings prevent the screws from falling
The retaining rings prevent the screws from falling
free from the bottom clamp and also aid in ease of
free from the bottom clamp and also aid in ease of
assembly.
assembly.
b. Remove the bottom clamp, the face ring assembly,
b. Remove the bottom clamp, the face ring assembly,
the glass lens, and the gasket from the fixture.
the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer to Section
Remove the gasket from the lens. Refer to
9, Exploded View and Replacement Parts. .
9, Exploded View and Replacement Parts
5.
Light Engine Replacement
a. 12V Small Light Engine (PCB) Replacement
a. 12V Small Light Engine (PCB) Replacement
1. Remove two (2) nuts and two (2) washers.
1. Remove two (2) nuts and two (2) washers.
2. Unplug the quick disconnect terminals from the
2. Unplug the quick disconnect terminals from the
light engine.
light engine.
3. Remove the light engine from the light fixture.
3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with
4. Place new light engine into the fixture with
orientation shown in Figure 7.
orientation shown in Figure 7.
5
5
Secure the light engine with one (1) nylon washer
Secure the light engine with one (1) nylon washer
and one (1) nut. Torque to 12 in-lbs.
and one (1) nut. Torque to 12 in-lbs.
6. Place a nylon washer on the other stud and place
6. Place a nylon washer on the other stud and place
the green ground wire terminal on the nylon
the green ground wire terminal on the nylon
washer and secure both with the nut. Torque to
washer and secure both with the nut. Torque to
12 in-lbs.
12 in-lbs.
Page 11
Light Engine (PCB)
Part Number
R0474000
R0474100
R0473900
R0473900
Section
the
the