Garden Treasures 247680 Manual rápido - Página 2

Navegue en línea o descargue pdf Manual rápido para Fuente al aire libre Garden Treasures 247680. Garden Treasures 247680 3 páginas. Boy & girl dancing fountain

Imprimir página
Assembly Instructions
1.
Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2.
Select a flat, level surface for the assembly and final location of your fountain.
3.
Place the basin on a level surface. Route the pump power cord from the cord slot on the bottom of the
basin. Insert the connector attached at the bottom of the statuary into the outlet on the pump. Then place
the cover onto the support platform. (As shown in Fig.1)
4.
Place the statuary onto the cover in an intended area. (NOTE: When placing the statuary onto the cover
be sure to line up the cover notches and the statuary notches). Fill the basin with clean water. The water
level should be even with the support platform. Arrange some pebbles on the cover for beautification if
needed. (NOTE: To ensure fine water effect, please keep pebbles away from jets). (As shown in Fig.2)
5.
Connect the pump power cord to the proper electrical outlet. Turn the power source on. Then the
product will begin to operate. (As shown in Fig.3) Splashing may occur when fountain is initially turned
on. If it happens, you may adjust the direction of the jets to eliminate splashing. If the jet is not working
check it to make sure the jet is unblocked. While cleaning and maintaining please return the thread cap
of the jet, remove and clean the jet. Then slip it into the thread cap and fix it to the socket. The product
will begin to operate again.
6.
To eliminate the possibility of water damage to areas around your fountain, check for leaks and
excessive splashing after the initial setup of your fountain. It is highly recommended that this fountain be
placed in an area that will not be damaged should the area come in contact with liquid.
7.
Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
8.
Check the area around your fountain on a regular basis to ensure that there is no leakage.
Pump Maintenance Instructions
•
Regular cleaning of the pump is necessary.
•
Keep water clean to prolong the life of pump.
•
Clean pump when it is dirty or when a drop in performance is detected. Use warm, soapy water and a
stiff brush for heavily stained surfaces. Do NOT use harsh chemicals, as this will damage the surface
finish.
•
Failure to clean the pump will result in overheating and voiding of the warranty.
•
Use a filter on pump if available.
•
Disconnect the power and empty the reservoir if the fountain will not be used for an extended time.
•
Do NOT operate fountain in temperatures below 41°F (5°C). Freeze damage may occur. If the fountain
is kept outdoors in freezing temperatures, make sure all water is removed and the unit is completely dry.
To disassemble pump for cleaning:
1.
Always disconnect pump from the power source before cleaning.
2.
Remove the inlet screen and impeller housing.
3.
Remove the impeller/rotor assembly by gently pulling on the impeller blades.
4.
Use a soft cloth or brush to clean the impeller/rotor assembly area inside the pump.
5.
Clean the inlet screen, impeller housing and impeller with warm, soapy water.
6.
Reassemble the pump and check for proper operation.
Hints and Troubleshooting
•
If the pump operates but there is no flow, check to make sure that the pump is fully submerged.
•
If the pump operates but there is no flow, check the supply tubing for kinks and correct.
•
If the pump operates but there is no flow, and if the pump is submerged and there are no kinks in the supply tubing, lift the pump out of the water.
Remove supply tubing at pump outlet and clean tubing inside and out if necessary. Put pump back into water (outlet side up). Once water begins to
flow, reattach the supply tubing.
TRANSFORMER INSTRUCTIONS:
IMPORTANT SAFETY INSTRUCTIONS
When using electrical product, basic precautions should always be practiced including the following:
1.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2.
Read and follow all instructions that are on the product or provided with the product.
3.
For a cord-connected or direct plug-in power unit, do not use an extension cord.
4.
Reference the National Electrical Cord, ANSI/NFPA 70, specifically for the installation of wiring and clearances from power and lighting
conductors.
5.
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-
rated construction.
6.
For a cord-connected or direct plug-in power unit, do not install or use within 10 feet of a pool.
2