Garden Treasures 247682 Manual de inicio rápido - Página 2

Navegue en línea o descargue pdf Manual de inicio rápido para Fuente al aire libre Garden Treasures 247682. Garden Treasures 247682 3 páginas. Vase fountain

Imprimir página
Estimated time for assembly is 15 minutes.
Tools required for assembly:
•
No tools required
Assembly Instructions
1.
Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2.
Select a flat, level surface for the assembly and final location of your fountain.
3.
Place the basin on a level surface. (Note: Route the pump cord from the cord slot on the bottom of
the basin). (As shown in Fig.1)
4.
Insert the one end of the plastic connector into the pump chamber. And insert the water supply tube
into the outlet on the pump. Then align the hole on the bottom of the vase with the other end of the
plastic connector. Finally, attach the vase onto the basin steady and levelly as shown in Fig.2. To
ensure fine watering effect, please make sure that the" "markings on the Vase and pump
chamber are just aligned together. (NOTE: Place the pump to the pump chamber).
5.
Fill the basin with clean water. The water level should be approx. 20mm below the top edge of the
basin. Arrange some pebbles on the vase for beautification. (As shown in Fig.3)
6.
Plug the pump power cord into the Ground Fault Circuit Interrupter (GFCI) outlet. Turn the power
source on. The product will be start operating. Splashing may occur due to the dry surface when
fountain is initially turned on. If it happens, use your fingers to wet entire surface. This should
eliminate splashing. (As shown in Fig.4)
7.
To eliminate the possibility of water damage to areas around your fountain, check for leaks and
excessive splashing after the initial setup of your fountain. It is highly recommended that this
fountain be placed in an area that will not be damaged should the area come in contact with liquid.
8.
Do not leave your fountain running for extended periods of time when no one is present to observe
the performance.
9.
Check the area around your fountain on a regular basis to ensure that there is no leakage.
Pump Maintenance Instructions
•
Regular cleaning of the pump is necessary.
•
Keep water clean to prolong the life of pump.
•
Clean pump when it is dirty or when a drop in performance is detected. Use warm, soapy water and
a stiff brush for heavily stained surfaces. Do NOT use harsh chemicals, as this will damage the
surface finish.
•
Failure to clean the pump will result in overheating and voiding of the warranty.
•
Use a filter on pump if available.
•
Disconnect the power and empty the reservoir if the fountain will not be used for an extended time.
•
Do NOT operate fountain in temperatures below 41°F (5°C). Freeze damage may occur. If the
fountain is kept outdoors in freezing temperatures, make sure all water is removed and the unit is
completely dry.
To disassemble pump for cleaning:
1.
Always disconnect pump from the power source before cleaning.
2.
Remove the inlet screen and impeller housing.
3.
Remove the impeller/rotor assembly by gently pulling on the impeller blades.
4.
Use a soft cloth or brush to clean the impeller/rotor assembly area inside the pump.
5.
Clean the inlet screen, impeller housing and impeller with warm, soapy water.
6.
Reassemble the pump and check for proper operation.
Hints and Troubleshooting
•
If the pump operates but there is no flow, check to make sure that the pump is fully submerged.
•
If the pump operates but there is no flow, check the supply tubing for kinks and correct.
•
If the pump operates but there is no flow, and if the pump is submerged and there are no kinks in
the supply tubing, lift the pump out of the water. Remove supply tubing at pump outlet and clean
tubing inside and out if necessary. Put pump back into water (outlet side up). Once water begins to
flow, reattach the supply tubing.
Pump is replaceable with model # PT-202 UL. Call Customer Service at 866-728-6187 for replacement parts.
SAVE THESE INSTRUCTIONS!
2