Avaya 5600 Series Manual de instalación rápida - Página 2

Navegue en línea o descargue pdf Manual de instalación rápida para Teléfono IP Avaya 5600 Series. Avaya 5600 Series 2 páginas. Gigabit, ip phones
También para Avaya 5600 Series: Instrucciones de instalación y seguridad (11 páginas), Manual de configuración (17 páginas), Ayuda para la instalación (14 páginas), Información sobre el producto (2 páginas)

Imprimir página

Avaya 5600 Series Manual de instalación rápida

Setting IP parameters using the console port and CLI Quickstart

To set IP parameters using the console port and CLI Quickstart, perform the following tasks:

Connect a terminal to the ERS 5600

1. Use a serial cable with a DB-9 connector at both ends to connect a terminal or PC to the console

port of the switch for initial configuration. A terminal or a PC with a terminal emulator can be used

as the management station. The following parameters must be used with any terminal emulation

application to connect to the switch.

2. Set the terminal protocol on the terminal or terminal emulation application to VT100 or VT100/ANSI.

3. Connect to the switch using the terminal or terminal emulation application.

4. The Avaya switch banner appears when you connect to the switch through the Console port.

There is no default password for the switch for CLI console access. Enter Ctrl+Y and type the

following CLI commands:

• enable

• install

Note: Avaya provides two console cable options to connect the ERS5600's DB9 (m) to a standard PC/Laptop DB9(m) or USB Serial

Adapter (purchased separately) for PC/Laptop with no native DB9(m).

1. A 1.5M Integrated RJ45/DB9(f) Console Cable (AL2011022-E6) in conjunction with a DB9(f)/RJ45 Adapter (AL2011020-E6)

2. Two DB9(f)/RJ45 Adapter (AL2011020-E6) connected together using a standard Cat5e Ethernet Cable (purchased separately).

The CLI Quickstart welcome screen helps you enter the information requested at each prompt.

Note: The ERS 5600 uses the default IP address of 192.168.1.1/24 if the switch does not get its IP address from

another source.

###############################################################################

Welcome to the 5650TD-PWR setup utility.

You will be requested to provide the switch basic connectivity settings.

After entering the requested info, the configuration will be applied and

stored into the switch NVRAM.

Once the basic connectivity settings are applied, additional configuration

can be done using the available management interfaces.

Use Ctrl+C to abort the configuration at any time.

###############################################################################

Please provide the Quick Start VLAN <1-4094> [1]:

Please provide the in-band IP Address [0.0.0.0]:

Please provide the in-band sub-net mask[255.255.255.0]:

Please provide the Default Gateway[0.0.0.0]:

Please provide the Read-Only Community String[**********]:

Please provide the Read-Write Community String[**********]:

Please provide the in-band IPV6 Address/Prefix_length[::/0]:

Please provide the in-band IPV6 Default Gateway[::]:

###############################################################################

Basic switch parameters have now been configured and saved.

###############################################################################

ERS 5600 Avaya Command Line Interface (ACLI)

You can manually load the ACLI script from the console menu or automatically load the script at startup.

Command Mode

User Executive

(Exec mode)

5600>

Terminal emulation settings

Property

Value

Privileged EXEC

Baud Rate

9600 bps

(PrivExec mode)

Data Bits

5600#

Stop Bits

Parity

None

Global Configuration

Flow Control

None

(Config mode)

5600(config)#

Interface Configuration

(ifconfig mode)

5600(config-if)#

Router Configuration

(config-router mode)

5600(config-router)#

Manual Configuration

You can manually configure the in-band management IP address at any time with the following ACLI command:

ip address <A.B.C.D> [netmask <A.B.C.D>] [default-gateway <A.B.C.D>]

Example:

1. Enter Privileged Exec mode: 5650>enable

2. Enter the Global Configuration mode: 5650#config terminal

3. Manually configure in-band management IP information:

ip address 172.16.1.80 netmask 255.255.255.0 default-gateway 172.16.1.1

4. Verify the information:

5650(config)#show ip [bootp] [dhcp] [default-gateway] [address [source]]

ACLI reboot parameters

Reboot the switch using one of the following commands:

boot - reboot the switch

boot default - reboot and use the factory default configuration

boot partial-default - reboot and use the partial factory default configuration

restore factory-default - reset the switch to factory default configuration