KitchenAid KESC300BWH1 Manual de instrucciones de instalación - Página 4

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Horno KitchenAid KESC300BWH1. KitchenAid KESC300BWH1 7 páginas. 30" (76.2 cm) electric slide-in range with self-cleaning thermal/convection oven
También para KitchenAid KESC300BWH1: Manual de uso y mantenimiento (5 páginas)

Imprimir página

Turn power supply off.

Electrical Shock Hazard

Do Not use two wire with a bare

grounding wire. All current-carrying

wires

must be insulated.

Failure to follow these instructions could

result in fire, electrical shock or death•

U-shard

hook

•

Figure

Direct wire preporolion

Strip outer covering back 3 inches (7.6 cm)

from end exposing the wires. (See Figure 8.)

Strip the insulation back 1 inch (2.5 cm) from

the end of each wire, Form the bare wire into a

"U" shaped hook, (See Figure 9.)

brass

terminal

block

cover

Figure 10

Remove the terminal block cover located on

)ack of range. Remove the 3/8" (0,95 cm) brass

terminal nuts attached to the knockout.

Do Not

remove

knockou L-_

conduit

connector

opening

Figure

Attach a U.L.-listed conduit connector to

the opening, Do Not remove the knockout.

Place power supply cable through conduit

connector, allowing enough slack to easily

attach the wiring to the terminal block. (See

Figures 11 and 12.)

si,v. ,ored ,/I

terminal

/ !

block screw _iL

groundi

link

onduit

Figure 12

Using the 3/8" (0.95 cm) brass nuts, attach

the neutral (white) of power supply cable to the

silver-colored center screw of the terminal

block. Place the hook-shaped end of the wire

over the terminal block screw with open side of

the hook facing to the right. Squeeze hook end

of wire together to form a loop.

Connect the other two wires to the outer

terminal block screws. Attach wires using the

same method as the neutral wire. (See Figure

12.)

Do Not loosen the factory-installed

nuts on the

terminal block,

Center wire MUST be connected to center

screw,

Tighten conduit connector, locking ring and

clamping screws.

7 • Reattach terminal block cover.

Panel C

Mobile home or other four-wire

installations:

Electrical Shock/Fire Hazard

Check that wiring you are using matches

colors shown in illustrations and specified

in instruction steps. If wiring does Not

match, it is your responsibility to have a

qualified electrician install the correct

wiring.

Failure to follow these instructions could

result in fire, electrical shock or death.

•

Turn power supply off.

brass

terminal

i/terminal

block

cover

Figure 13

Remove the terminal block cover located on

back of range. Remove the 3/8" (0.95 cm) brass

terminal nuts attached to the knockout.

Remove knockout

,pening for

Figure

Remove the knockout for the 40-ampere

power supply cord.

Attach a 3/4" (1.9 cm) U.L.-listed strain

relief (U.L marking on strain relief) to the

opening. Tighten strain relief firmly to cabinet.

Place power supply cord through strain relief.

link screw

Figure

Remove the grounding-link screw from the

range frame. Save the grounding-link screw,

Bend up the grounding link so that it does not

contact the range.

silver-

,_ IIH/

\\/l

\\_l

colored

terminal

block

screw

Green

wire

insulated

_re

MUST

connected

before

connecting

neutral

- (white)

_.,U.L. listed

Figure

strain relief

Connect the green grounding wire to the

range using the grounding-link screw removed

in Step 5. The green grounding wire must be

attached first and must Not contact any other

terminal.

Using the 318" (0.95 cm) brass nuts,

attach the neutral (white) wire of power supply

cord to the center, silver-colored screw of the

terminal block.

Connect the other two wires to the outer

terminal block screws. (See Figure 16.)

Do Not loosen the factory-installed

nuts on the

terminal block.

Be sure the wiring nuts are installed tight.

Tighten strain relief screws.

9o Reattach terminal block cover.

Turn power supply off.

J_(7"3"cm---'_)

U-shaped

hook

Figure

Direct wire preparation

Strip outer covering back 3 inches (7.6 cm)

from end exposing the wires. (See Figure 17.)

Strip the insulation back 1 inch (2.5 cm) from

the end of each wire. Form the bare wire into a

"U" shaped hook. (See Figure 18,)

_'_

.. terminal

block

brass

cover

terminal

Figure

Remove the terminal block cover located on

back of range. Remove the 3/8" (0.95 cm) brass

terminal nuts attached to the knockout.

Do Not

conduit

remove

connector

I_ockout_

Figure 20

U.L listed

COnduit

Attach a U.L.-listed conduit connector to the

opening. Do Not remove the knockout. Place

power supply cable through conduit connector,

allowing enough slack to easily attach the wiring

to the terminal block. (See Figures 20 and 21 .)

Figure

Remove the grounding-link screw from the

range frame. Save the grounding-link

screw.

Bend up the grounding link so that it does not

contact the range.

silver-

colored -

terminal

block

screw

Green

insulated wire

MUST be

Connected

before

connecting

other wires.

,(white)

wire

', U.L. listed conduit

connector

Figure

Connect the green grounding wire to the

range using the grounding-link

screw removed

in Step 5. The green grounding wire must be

attached first and must Not contact any other

terminal.