Gardena 1499 Manual de instrucciones - Página 4

Navegue en línea o descargue pdf Manual de instrucciones para Bomba de agua Gardena 1499. Gardena 1499 9 páginas. Deep well pump

Imprimir página

1. Trouble-Shooting

For Art. 1499 only:

Before putting the pump into operation or switching it on,

Bleeding:

please note: When first put into operation, the pump takes

about 60 seconds to vent after submersion in the water.

v Put the pump into operation only after this 60-second

submersion phase.

Once the pump has been put into operation, the end of the bleed ing

operation is indicated by a jet of water exiting the bleed openings.

For Art. 1499 only:

The pump pumps and switches off automatically as soon as

Automatic mode:

no more water is drawn. Due to the check valve, the pressure is

maintained in the hose until water is drawn via the hose.

When water is drawn via the hose (the pressure in the hose falls

below 3.5 bar), the pump switches on automatically.

For Art. 1499 only:

The pump switches off automatically when there is no fluid

Dry run protection

pumped (the pump operates in cycles 30 secs. on – 5 secs. off

(flow control):

(4x). This cycle is repeated in 1 hr, 5 hrs, 24 hrs, 24 hrs ... ).

As soon as the inlet filter of the pump is again submersed at least

15cm in the water, the pump is ready to operate again.

For Art. 1499 only:

The flow control switches off automatically as soon as no more

Flow control:

water is drawn. In the event of leakage on the pressure side

(e. g. leaking pressure hose or tap) switches the pump on and off at

short intervals. If the pump is switched on and off more frequently

than 7 x in 2 min. (with a leakage < 200 l/hr), the pump switches off

completely. When the leakage on the pressure side is eliminated,

the pump must be unplugged and plugged in again in order to be

operational again.

For Art. 1499 only:

The built-in non-return valve prevents the water flowing back

Non-return valve:

through the pump.

5. Putting into Storage

Storage:

The storage location must not be accessible to children.

v Store the pump away from frost before the first frost sets in.

Disposal:

The product must not be added to normal household waste.

(in accordance with

It must be disposed of in line with local environmental regulations.

RL2002/96/EC)

6. Maintenance

Clean priming area:

1. Unscrew both screws

2. Clean priming area of the pump and inlet filter

3. Fix inlet filter

with the two screws

DANGER! Electric shock!

There is a risk of injury from electric

shocks.

V Disconnect the Deep Well Pump from the mains

power supply before carrying out maintenance.

and remove the inlet filter

around the priming area again and screw tight

7. Trouble-Shooting

Fault

Pump is running,

but doesn't deliver.

Pump doesn't start or

suddenly stops during

operation.

Pump runs, but output

suddenly decreases.

For any other malfunctions please contact the GARDENA service department.

Repairs must only be carried out by GARDENA service departments or specialist

dealers authorised by GARDENA.

DANGER! Electric shock!

There is a risk of injury from electric

shocks.

V Before eliminating faults, disconnect the Deep

Well Pump from the mains power supply.

Possible cause

Remedy

Air cannot escape as the

v Open pressure line

pressure line is closed.

(e. g. bent pressure hose).

Priming area blocked.

v Disconnect mains plug

and clean priming area

(see 6. Maintenance).

When starting the pump,

v Immerse pump deeper

water height falls below the

(observe minimum water

min. water level.

level: see 9. Technical Data).

Non-return valve blocked.

v Art. 1499:

Contact GARDENA Service.

Thermal protection switch

v Disconnect mains plug

switched pump off due to

and clean priming area

overheating.

(see 6. Maintenance).

Observe max. media

temperature (35 °C).

Power supply interrupted.

v Check fuses and electrical

plug-in connections.

Dirt particles are trapped in

v Disconnect mains plug

priming area.

and clean priming area

(see 6. Maintenance).

Priming area blocked.

v Disconnect mains plug

and clean priming area

(see 6. Maintenance).

For Art. 1499 only: Lack of

The pump is only operational

water: Dry run protection

when it is submerged at least

switched the pump off due to

15 cm.

insufficient water level.

v Submerge pump at least

15 cm in water.