Gardena 2000/2 18V P4A Manual del usuario - Página 8
Navegue en línea o descargue pdf Manual del usuario para Bomba de agua Gardena 2000/2 18V P4A. Gardena 2000/2 18V P4A 18 páginas. Battery submersible pump/battery rain water tank pump
Imprimir página
1. Push the Flow button
(m)
The current power level is displayed for 5 seconds.
2. Push the Flow button
(m)
edly until the desired power level is displayed.
Depending on environmental conditions (e. g. direct sun-
light), the pump can activate the overheating protection.
A short cooling phase may then be necessary before
restarting.
Timer-Function:
With the timer function the pump can be switched off auto-
matically after 5, 10 or 15 minutes.
Displays when selecting the timer time:
(L1)
flashes green and blue alternately
(L1)
(L2)
and
flashes green and blue
alternately
(L1)
(L2)
(L3)
,
and
flashes green and blue
alternately
1. Push and hold the Flow button
LED
(L1)
flashes green and blue alternately.
(m)
2. Push the Flow button
edly until the desired timer time is displayed.
If no button is pressed for 5 seconds, the timer func-
tion will start. The pump runs according to the selected
timer time and then switches off automatically.
Displays after starting the timer function:
Timer-Time
Timer-Time
15 min.
10 min.
Approx.
Approx.
15 – 10 min.
10 – 7 min.
Approx.
Approx.
10 – 5 min.
7 – 3 min.
Approx.
Approx.
5 – 0 min.
3 – 0 min.
For the last 5 seconds the blue LED
After starting the timer function, first the timer time is dis-
played 5 times in blue LEDs and then 1 time the battery
charge status in green LEDs for one second.
Notes:
The timer function can be cancelled at any time by
pressing the On / Off button.
If the battery runs out during the timer function, the pump
switches off early.
Applications:
CAUTION! Destruction of the battery!
The battery unit is destroyed when they are
immersed in water.
v Do not immerse the battery unit in the water.
Observe the minimum water level (see 7. TECHNICAL
DATA).
18
on the control panel.
on the control panel repeat-
Timer to 5 minutes
Timer to 10 minutes
Timer to 15 minutes
(m)
for 3 seconds.
on the control panel repeat-
Timer-Time
Timer display in
5 min.
blue LEDs
(L1)
(L2)
(L3)
Approx.
,
and
5 – 3 min.
go out sequen-
tially
(L1)
(L2)
Approx.
and
go out
3 – 1 min.
sequentially
(L1)
Approx.
goes out
1 – 0 min.
(L1)
flashes rapidly.
Use in flat containers [ Fig. O5 ]:
Art. 14600: The pump is equipped with a hose connector
which allows high flow rates.
Art. 14602: If the rain water tank pump is placed in flat
containers, e. g. to empty a paddling pool, the telescopic
pipe can be removed and replaced with the 33.3-mm (G1)
GARDENA Tap Connector Art. 18202.
(D)
1. Place the battery unit
water.
2. Place the pump in the container.
3. Start the pump.
Flat suction [ Fig. O6 ]:
In normal operation (with foot
of approx. 25 mm is achieved. With flat suction (without
(9)
foot
) a residual water level of approx. 5 mm is achieved.
(9)
1. Turn the foot
anti-clockwise and remove the foot
(bayonet lock).
2. Make sure that the filter
3. For reassembling the suction foot,
see 4. MAINTENANCE.
The pump must not be operated without the filter
To pump water from container [ Fig. O7 ]:
For Art. 14602: The length of the telescopic pipe
should be adjusted in such a manner that the pump does
not touch the bottom of the container; this way, dirt in the
container is kept away from the pump.
The pump should hang approx. 10 cm above the bottom
of the container to prevent excessive contamination.
1. Open the bracket on the battery container
(D)
2. Hang the battery unit
the container or place it in a suitable, flood-proof place.
3. For Art. 14600: Hang the pump into the container
using a rope (do not hang it with the cable).
For Art. 14602: Hang the pump with the telescopic
(3)
tube
into the container.
4. Start the pump.
To start the pump [ Fig. O1 / O4 ]:
To start:
(8)
1. Open the cover
.
2. Put the battery
(B)
into the battery holder
audibly engages.
3. Close the cover
(8)
until it engages noticeably.
Make sure that the cover
properly closed.
4. Push the On / Off button
The Pump starts and the battery charge status
indication is displayed.
NOTES:
Depending on the length of the hose and the type
of installation, it may take some time for the pump
to deliver the water.
If the pump does not deliver water after several
suction attempts, there is probably air in the hose.
v Start the pump once briefly in water without
a hose.
in a place protected from
(9)
), a residual water level
(10)
is inserted correctly.
(10)
.
(3)
(D)
.
on the outside, on the side of
(D)
until it
(8)
of the battery container is
(s)
(P)
on the control panel
(9)
.