KitchenAid GZ7930XHS1 Manual de uso y mantenimiento - Página 2

Navegue en línea o descargue pdf Manual de uso y mantenimiento para Campana de ventilación KitchenAid GZ7930XHS1. KitchenAid GZ7930XHS1 16 páginas. 30"/36" retractable downdraft vent systems

Imprimir página

Your

safety and the safety of

others are very important.

We have provided many important

safety messages in this manual

and on your appliance. Always

read and obey all safety

messages.

This is the safety alert

symbol.

This symbol alerts you to

potential hazards that can kill or

hurt you and others.

All safety messages will follow the

safety alert symbol and either the

word "DANGER" or "WARNING".

These words mean:

You can be killed or seriously

injured if you don't immediately

follow instructions.

You can be killed or seriously

injured if you don't follow

instructions.

All safety messages will tell you

what the potential hazard is, tell you

how to reduce the chance of injury,

and tell you what can happen if the

instructionsare not followed.

IMPORTANT: Observe all governing

codes and ordinances.

Failure to meet codes and

ordinances

could lead to fire or

electrical

shock.

Proper installation

is your

responsibility.

Make sure you have

everything

necessary for correct

installation. It is the responsibility

of the installer to comply with the

installation clearances

specified

the model/serial

rating plate.The

model/serial

rating plate is located

on the front of the downdraft

vent

above the wiring

box cover.

Check location where downdraft

vent will be installed.The

location

should

be away from strong draft

areas, such as windows,

doors and

strong heating vents or fans.

Before making countertop

cutout,

check that downdraft

vent and

cooktop

location will clear cabinet

walls, backsplash,

and rear wall

studs inside cabinet.

Mobile home installation

The installation of this downdraft

vent system

must conform

to the

Manufactured

Home Construction

Safety Standards, Title 24 CFR,

Part 328 (formerly

the Federal

Standard

for Mobile

Home

Construction

and Safety, Title 24,

HUD, Part 280) or when such

standard

is not applicable,

the

Standard

for Manufactured

Home

Installation

1982 (Manufactured

Home Sites, Communities

and

Setups) ANSI A225.1/NFPA 501A*,

or latest edition,

or with local

codes.

All openings

in the wall or floor

where retractable

downdraft

vent

is to be installed

must be sealed.

Electrical

ground is required.

See

"Electrical

requirements:'

page 3.

When installing downdraft

vent,

the cabinet drawer will need to be

removed

and the drawer front

installed permanently

to cabinet.

NOTE: Downdraft

vent is installed

directly

behind the cooktop. Install

downdraft

vent first.

Cabinet construction:

Downdraft

vent is designed

for use in a

cabinet with a depth of 24"

(61 cm). Some installations

require a countertop

deeper than

25" (63.5 cm). See chart on page 5.

The maximum

depth of the

overhead

cabinet is 13" (33 cm).

Overhead

cabinets

installed at

either side of the downdraft

vent

must be 18" (45.7 cm) above the

cooking surface.

See cooktop

Installation

Instructions

before making any

cutouts and for the minimum

distance between the front edge

of the countertop

and front edge

of cooktop.The

minimum

horizontal

distance

between the

overhead

cabinets

is the same as

the width of the installed

downdraft

vent.

When installing a 36" (91.4 cm)

retractable

downdraft

vent with

"Create-A-Cooktop"

modules,

the

optional

support must be installed

on the front of the downdraft

vent.

See installation steps for details.

Parts supplied

for installation:

® 1 top trim

2 end caps

2 lower

support

legs

® 2 overcounter

support

brackets

e 2 undercounter

mounting

brackets

® 1 bag of fasteners

® 1 metal

cover

1 backdraft

damper

® literature

package

e optional

support

and two

screws

(36"

(91.4 cm) models

only

Parts needed

for installation:

®2 U.L.- or C.S.A.-listed

1/2" (12.7 ram)

conduit connectors (3 are required if

the exterior-mounted vent motor

is used.)

* 1 wall cap for interior-mounted

motor

® vent

system

power supply cable

wiring cable for optional remote

blower kit.

Tools needed for

installation:

e safety

glasses

e gloves

jig or keyhole saw

,' drill with 1/8" drill bit

o pencil

® measuring

tape

,' flat-blade screwdriver

Phillips screwdriver

e 3/8" (9.5 ram)

nut driver or ratchet

e level

® pliers

® metal

snips

® wire

stripper

or utility

knife

® caulking

gun and

weatherproof

caulk

e duct

tape