KitchenAid 3184435 REV. A Instrucciones de instalación - Página 2

Navegue en línea o descargue pdf Instrucciones de instalación para Horno microondas KitchenAid 3184435 REV. A. KitchenAid 3184435 REV. A 5 páginas. 27” electric built-in combination microwave and thermal oven, microwave and thermal convection oven, microwave convection and thermal convection oven

Imprimir página
27" Thermal and Thermal
Convection
Double ovens
Before you start...
Read the electricaT and carpentry
instructions.
Proper installation
is your responsibility.
A
qualified technician should install this oven.
Make sure you have everything
necessary for
correct installation.
It is the responsibility
of the
installer to comply with the installation
clearances specified on the serial/rating
plate.
The serial/rating
plate can be found behind the
oven door on the front frame of the oven.
Check location
where the built-in oven will be
installed. The location should be away from
strong draft areas, such as windows, doors, and
strong heating vents. The built-in oven should
be located for convenient
use in the kitchen.
Remove all packaging
material from
microwave oven cavity. Check microwave oven
area for damage - see WARNING below. If
any damage is evident, do not operate until
microwave oven is checked by an authorized
service technician.
Cabinet opening
dimensions
that are shown
must be used. Given dimensions
provide
minimum clearance. Contact surface must be
solid and level and flush with the bottom.
The recessed
installation
area must provide
complete enclosure around the recessed
portion of the oven.
ALL OPENINGS
IN THE WALL OR FLOOR
WHERE THE BUILT-IN OVEN IS TO BE
INSTALLED
MUST BE SEALED.
Electrical
ground
is required. See "Electrical
requirements."
Cabinet
door
P
'Note:
There must be 1"
min. between
bottom
of
cabinet
door and top of
oven console.
Oven control
4-112" exoosed
trim, do&r and
27" min.
cabinet
width
I
L
e4-L
\
\
Do Not',
seal oven
\
to cabinet.
'
\
24" min. overal
cabinet
depth
idle depth
/2" without
die\.
I i
opening
49"
I
depth
cabinet
I
7
49-7/w
-
overall
height
See Note:
opening
height
i
I
I
I
I
I
I Electrical
supply junction
1 box
46-13/16"-
ret :es
hl eic
;sed
Iht
nin.
1
1
H
11" min.
I
NOTE:
I
I
The oven support
surface
must be flush
with the bottom of the cabinet
cutout.
I
ordinances.
overall
width
\Thermal
- 23k6"
Thermal
convection
-
h
Cabinet
Damage
Do Not block the oven vent.
Blocking
the oven vent may cause cabinet
damage and poor baking performance.
Excessive
Microwave
Energy Exposure
l
Do Not attempt to operate the microwave
oven with the door open.
l
Do Not tamper with or defeat the safety
interlocks.
l
Do Not place objects between
the
microwave
oven front face and door.
l
Do Not allow soil or cleaner
residue to
accumulate
on sealing
surface of the
microwave
oven door.
. Do Not operate the microwave
oven if
damaged.
l
Do Not operate the microwave
oven if:
- door is bent.
-
hinges and latches are broken or
loose.
- door seals, sealing
surfaces
or
glass are broken.
The microwave
oven door must close
properly
to provide
safe operation.
b Only have a qualified
repair person
adjust, repair and check microwave
oven
for microwave
leakage after a repair is
made.
b Do Not use microwave
for commercial
purposes.
The microwave
oven in this
unit is designed
for household
use only.
Failure to follow these instructions
could
result in exposure
to excessive
microwave
5nerav.
Tools needed for
installation:
If codes permit and a separate
grounding
wire is used, it is recommended
that a
qualified
electrician
determine
that the
grounding
path is adequate.
IMPORTANT:
Save Installation
Instructions
for the local
electrical
inspector's
use.
screwdriver
IA
This appliance must be connected to
. the proper electrical voltage and
frequency as specified on the serial/rating
plate
located behind the oven door on the front frame.
Models rated at 7.0 kw on 240 volts (5.3 kw on
208 volts) or more require a separate
40-ampere circuit. Models rated at 3.6 kw on
240 volts (2.7 kw on 208 volts) or less require a
separate 30-ampere circuit. Fuse both sides of
the line. A time-delay fuse or circuit breaker is
recommended.
'arts supplied
'or installation:
Electrical
requirements
(BJ
OVEN MUST BE CONNECTED
WITH
. COPPER WIRE ONLY.
ICI
Wire sizes and connections
must
. conform to the reauirements
of the
National Electrical Code, ANSI/NFPA
70 -
latest edition**, and all local codes and
ordinances.
Wires sizes and connections
must
conform with the rating of the appliance.
Copies of the standards listed may be obtained
from:
**National
Fire Protection
Association
Battetymarch
Park
Quincy,
Massachusetts
02269
Electrical
Shock Hazard
l
Electrical
ground
is required
on this
appliance.
l
Do Not ground to a gas pipe.
l
Do Not have a fuse in the neutral or
grounding
circuit.
A fuse in the neutral or
grounding
circuit
could result in an
electrical
shock.
l
Check with a qualified
electrician
if you
are in doubt as to whether
the appliance
is properly
grounded.
Failure to follow these in instructions
could result in serious
injury or death.
Electrical
Shock Hazard
It is the customer's
responsibility:
l
To contact
a qualified
electrical
installer.
l
To assure that the electrical
installation
is
adequate
and in conformance
with
National
Electrical
Code, ANSUNFPA 70 -
latest edition**,
and all local codes and
ordinances.
Failure to do so could result in fire,
electrical
shock or other personal
injury.
Personal
Injury Hazard
Securely
fasten oven to cabinet
using the
screws
provided.
Failure to do so could cause the oven to
move or tip during
use and result in
personal
injury.
_ -
Panel A