Gardena 1265 Manual del usuario - Página 5
Navegue en línea o descargue pdf Manual del usuario para Sistema de riego Gardena 1265. Gardena 1265 12 páginas. Holiday watering set
También para Gardena 1265: Manual de instrucciones (20 páginas), Manual de instrucciones (17 páginas), Manual del usuario (13 páginas)
Imprimir página
away from direct sunlight). Preferably place them
around 1 metre away. Bear in mind that a plant's water
requirements may change if its position is changed. If its
position is bright and warm, its water requirements will be
higher than in a cool, shady position.
CAUTION!
The plants must be positioned above the water
level of the reservoir to prevent the water from
the reservoir from flowing out via the supply pipes.
1. Group your plants in 3 groups according to their water
requirements.
2. Use planters or saucers so that any excess water will be
collected.
3. Allocate the individual drip distributors to the groups.
To connect the supply pipes to the pump
[ Fig. I1 / I2 ]:
The pump has 3 connections
(4)
1. Slide the sleeve
onto the supply pipe
(3)
2. Slide the supply pipe
(11)
tions
.
(4)
3. Screw the sleeve
onto the connection
4. If you do not use all 3 drip distributors, screw the end
(5)
caps
onto the unused connections
4. OPERATION
DANGER! Risk of injury!
Risk of injury when the product starts
accidentally.
v Disconnect the product from the mains before
you fill the container.
To start the watering [ Fig. O1 ]:
CAUTION!
Damage to the pump if it runs dry.
v Make sure that the container is always
sufficiently filled with water.
5. MAINTENANCE
DANGER! Risk of injury!
Risk of injury when the product starts
accidentally.
v Disconnect the product from the mains before
you maintain the product.
12
(11)
(3)
for supply pipes
.
(3)
.
onto one of the three connec-
(11)
.
(11)
.
Connecting the drip distributors to the supply pipes
[ Fig. I3 ]:
1. Cut the supply pipe perpendicular to its length
position where you are setting up the drip distributor
(4)
2. Slide the sleeve
onto the supply pipe
(3)
3. Push the supply pipe
(6)
distributor
until it reaches the stop.
4. Screw the threaded collar
(6)
drip distributor
.
Connecting the drip pipe to the drip distributor
[ Fig. I4 ]:
(8)
1. Cut the drip pipe
perpendicular to its length.
(8)
2. Push the drip pipe
onto the connection on the drip
(6)
distributor
until it reaches the stop.
(8)
3. Cut the drip pipe
at an angle at the position where
you want to water.
This ensures that the water will drip more efficiently.
4. Close unused connections of the drip distributor
(7)
the plugs
.
Fitting the drip pipe to the pipe peg [ Fig. I5 ]:
(9)
1. Place the pipe peg
into the soil of the plant at the
desired position.
(8)
2. Clip the drip pipe
into one of the 3 holding fixtures on
(9)
the pipe peg
in such a way that the drip pipe is facing
downwards.
If a plant has higher water requirements, several drip pipes
can be fitted to a hose bracket.
1. Fill the container with the previously calculated
amount of water (make sure that the container
stands in a secure position).
2. Place the pump in the container filled with water
(make sure that the pump is level with the bottom of
the container).
(2)
3. Connect the pump
to the power adapter
4. Plug the power adapter
The watering will start for 1 minute and the control
(Lc)
indicator
will illuminate green.
5. During the first watering, check all connections for leaks.
The watering will be repeated daily at the same time as the
power adapter was plugged in.
To clean the pump:
DANGER! Risk of injury!
Risk of injury and risk of damage to the
product.
v Do not clean the product with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or
solvents. Some can destroy critical plastic parts.
(3)
at the
(3)
.
onto the connection on the drip
(4)
onto the connection on the
(6)
(1)
.
(1)
into an electrical socket.
(6)
.
with