Makita 6223D Manual de instrucciones - Página 8

Navegue en línea o descargue pdf Manual de instrucciones para Taladro Makita 6223D. Makita 6223D 12 páginas. Cordless driver drill
También para Makita 6223D: Manual de instrucciones (11 páginas)

Imprimir página

1. Specifications

For DC1414

Plug the battery charger into the proper A/C voltage source. The charging light will flash in green color. Insert the bat-

tery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective

markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When

the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The

charging light will remain lit steadily during charging. When the charging light color changes from red to green, the

charging cycle is complete. The charging time is approximately one hour.

If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its

"trickle charge (maintenance charge)" mode. After charging, unplug the charger from the power source. Refer to the

table below for the charging time.

Battery type

1220 (Ni-cd)

1233 (Ni-MH)

1234 (Ni-MH)

1235 (Ni-MH)

CAUTION:

• The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufac-

turer's batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location

exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a

while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the

battery cartridge from the battery charger.

• If the charging light flashes alternately in green and red color, a problem exists and charging is not possible. The ter-

minals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

Trickle charge (Maintenance charge)

If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will

switch into its "trickle charge (maintenance charge)" mode and keep the battery cartridge fresh and fully charged.

Tips for maintaining maximum battery life

Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before charging it.

Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

Installing or removing driver bit or drill bit (Fig. 3)

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as

it will go. Hold the ring firmly and turn the sleeve clock-

wise to tighten the chuck. To remove the bit, hold the ring

and turn the sleeve counterclockwise.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Capacity (Ah)

1.3

2.2

2.6

3.0

Number of cells

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction of

rotation. Slide the reversing switch to the left for clock-

wise rotation or to the right for counterclockwise rotation.

Adjusting fastening torque (Fig. 6)

The fastening torque can be adjusted in six stages by

turning the adjusting ring so that the pointer on the

adjusting ring points to a number on the tool body. The

fastening torque is minimum when the pointer points to

the number 1 and maximum when it points to the

marking. The clutch will slip at varying torque

levels when the pointer is set at the numbers 1 to 5. The

clutch is designed not to slip at the

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

Charging time

Approx. 30 min.

Approx. 50 min.

Approx. 60 min.

Approx. 70 min.

marking.