Alinco DM-330MV Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Fuente de alimentación Alinco DM-330MV. Alinco DM-330MV 2 páginas. Switching mode dc regulated power supply
También para Alinco DM-330MV: Manual de ajuste (14 páginas)

Imprimir página

ALINGO

REMOTE CONTROLLER

The DM-330MV does not

include a remote controller.

Nor is it available as an

optional accessory. lt can

be easily assembled using

the diagram provided. The

adiustable voltage ranges

from approximately 5-15

volts.

3.5mm stereo plug

CAUTION

"The remote controller must be assembled exactly as the diagram shows.

Using SP resistors of different values can damage the unit and will void

the warranty.

'When the remote controller is connected, the unit must be turned off.

The maximum length of cable.that should be used is 1.5m or Sft.

ll.\l Al lNeO lNC.

l - n r . n r c o l n r r l l Y Y t l l

Head

Otfice:

'TwlN

21" MIO Tower

Building

25F

1-61. 2-Chome,

Shlromi,

Chuo-ku,

Oska

54O-858O, Japan

Phone: 06-691+6-8150

Fd:

06€946-4175

Thank you lor purchasing the Alinco switching

mode DC regulated power supply, DM-3301,4/.

The DM-330MV instruclion manual contains

important safety and operating instructions.

Read this manual carefully belore using this

Droduct. Keeo the manual for future reference.

ALtNCO,tNC.

INTRODUCTION

Alinco's DM-33OMV

is a high ef6ciency...compacl lightweight high perfomance

switching mode power supply- It is a.lso engineered to minimize the switching noise

specifcally for communication use- Even whea noise occurs. it may be eliminated with

tle Noise-Ofbet function. Also convenient functions like pre-set voltage, remote control

and a highly visible back lit meter are stardard in this power supply.

PRESET FUNCTION

When this function is activated, a preset voltage will be supplied regardless of the cunent

voltage setting. To store the preset voltage, tum the switch to the pres€t positbn and

adjust the preset voltage to the desired output level. When this lunction is selected the vol-

tage adiustment control on the front panel will be deactivated to proted trom over vottage.

SPECIFICATIONS

Inputvottage:

120VAC(MVD/230VAC(M\r4

Outputvollage:

5-15VDCvariable

Oiput volt4e Egdation: less than 2%

Protection:

short-circuit, Automatic cunent limiting over 32A

over-temp6rature

Outputc1Jr'gnt

32A(max), 3oA(continuous)

Rippl6:

less than 1smvp-p at raled load

Fuse:

8A(MVT)/4A(M\Z)

Meter:

single volt / cunent meter, back-lit

Dimensions:

1 75(W) x 67(H) x 1 65 (D) mm

Weiglrt

approx.2kg

E-mail: export@[email protected]

u.S.A.: 438 AmFla

Ave., Unit 13O, Tomn@,

CA 905'01'6201, U.S.A.

Ph@6: 31ffi 1 8-8616 Fd: 31OGl8-8754

htF/A/ww.alin@.@rnl

Gcrmany:

EschtDmr

Landatre

55,6o4a0 FranKun

am Main, Gemany

PtFm:

069-78€018

Fd:

069-789€0766

hb:/

tw.di|E.dal

O1999 Akp,

|rc., Os8l€, J€psl. AI rtdtts lwwd.

Alhough AI@ h6 (bsigred rils |llrud

to b€ 6 wnpd€nsh€

9nd @rate

6 po$ilte, re ffi

dght to make

cfErE$ ai $y fire to the dterit6

d u

spsifcati(rc.

Pbe

rcte thd ddn

prodrEis 9nd @eswies

ruy not b€

a€ihbl€ h aI @untn€ of dbtnbt iI.

Pl€e trsJt

]err Anhqized AFE Deal€r {cr hf@tih.

PART NAMES AND FUNCTIONS

Front View

Rear View

o @oo

(

Q Power switch: Tums the unit on and off.

Meter switch:

Select the position to indicate voltage M or cunent (4.

O maen

Displays the voltage or cunent,

lO Snap in output terminat:

5A max. Red positive, black negative.

cigarette ptug t€rminal:

10A max.

(D Preset indicaton

Lights up when preset function is activated.

Q eroteAnon indicatot:

Lights up as a waming when the cunent limiting system is

activaled.

Pow6r indicator:

Lights up when the unit is tumed on.

(D Voirage adiustm€nt

Adiusts voltage between 5.0 and 15.0 votts. Tum clockwise to

increase and counter clockwise to decr€ase the vottage. When it is set at the center

position it will Eupply 13.8 volts.

(D noise off-set volume cortrol:

Adjust to eliminate the pulse noise of the switching

circuit. This patent pending function is specially designed lor communication use.

(lt's effectiveness may vary dep€nding on the frequency and mode.)

Cooling fanl

The fan tums on and off automatically.

O Remote control terminal:

By conn€cting a remote controller, the output voltage can

be remote controlled.'Note: Whon the r€mole control is connected to the unit, the

unit must be tumed off. When the remote control is being used the voltage

adiustment knob and preset function will be deactivated.

(p Prcset volume:

see (D

@ Presa swilch:

To store the preset voltage, tum this switch to the preset position

and adjust the preset volume to the desired output level.

O Heat sink:

Do not touch the surface when the unit is in use. Let the unit cool down

completely before touching it.

O Grounding screw: Used to connect the Earth grounding cable to the unit,

O Output terminat: 32A max. Red positive, black negative.

Q Power cable: 12OVAC outlet (MW)/23oVAC outlet (MVa

(D Fuse: sAO,lVD/4A(M\z)

CAUTION

1. Even though the chassis of the unit is

negatively grounded, use the conegt t€r-

minals to connect cable.

2.When plugging the unit into a wall out-

let. it must be tumed off.

3. Place the unit in a dry and wellventi-

lated area.

4. Never touch the unit while in use. Even

though it is designed for high efiiciency,

the unit will still get hot. lf the unit reach-

es a certain temperature, the "e)Creme

temperaiure protection" tunction will

protect the unit by automatically drop-

ping the cunent down to a sale level

and the protection indicator will light up.

5. A current limiting system wfil protect

the unit from overloading.

6. lf a short circuit occurs at the output,

the unit is protected by a short circuit

protection tunction. lmmediately tum

off the unit and repair the cause of the

short circuit. then tum it back on.

7.Do not use the unit for devices that

require high curTent input at the start,

such as motorized equipment. Do not

use the unit to charge a car battery.

8. Do not use a car cigarette lighter in the

cigarette plug socket on the unit,

L Before r6placing a fuse make sure the

unit is tumed off. Be sure to use the

specilied type of tuse.

1o.Make sure the product is always suit-

ably grounded to prevent electric

shock and to reduce noise. (fhe unit

can be grounded by connecting a

grounding cable to the appropriate

screw)

1l.Never disassemble, modity, or touch

the inside of the unit unnecessarily.

This could cause damage to the pro.

duct and will void the wanantv.

DM-33OMV

@ @ ( E @ @