Garmin fenix 2 Manual del usuario - Página 19

Navegue en línea o descargue pdf Manual del usuario para Ver Garmin fenix 2. Garmin fenix 2 26 páginas. Sports and fitness gps-devices
También para Garmin fenix 2: Manual rápido (25 páginas), Manual de inicio rápido (4 páginas)

Imprimir página

1. Clock

The Garmin logos on the module and the strap should be

right-side up.

Wet the electrodes

on the back of the strap to create a

strong connection between your chest and the transmitter.

If the heart rate monitor has a contact patch

contact patch.

Wrap the strap around your chest, and connect the strap

hook

to the loop

The Garmin logos should be right-side up.

Bring the device within 3 m (10 ft.) of the heart rate monitor.

After you put on the heart rate monitor, it is active and sending

data.

TIP: If the heart rate data is erratic or does not appear, see the

troubleshooting tips

(Tips for Erratic Heart Rate

Tips for Erratic Heart Rate Data

If the heart rate data is erratic or does not appear, you can try

these tips.

• Reapply moisture to the electrodes and contact patch.

You can use water, saliva, or electrode gel.

• Tighten the strap on your chest.

• Warm up for 5–10 minutes.

• Wash the strap after every seven uses

Rate

Monitor).

• Wear a cotton shirt or wet your shirt if suitable for your

activity.

Synthetic fabrics that rub or flap against the heart rate

monitor can create static electricity that interferes with heart

rate signals.

• Move away from sources that can interfere with your heart

rate monitor.

Sources of interference may include strong electromagnetic

fields, some 2.4 GHz wireless sensors, high-voltage power

lines, electric motors, ovens, microwave ovens, 2.4 GHz

cordless phones, and wireless LAN access points.

• Replace the battery

(Replacing the Heart Rate Monitor

Battery).

ANT+ Sensors

Foot Pod

Your device is compatible with the foot pod. You can use the

foot pod to record pace and distance instead of using GPS

when you are training indoors or when your GPS signal is weak.

The foot pod is on standby and ready to send data (like the

heart rate monitor).

After 30 minutes of inactivity, the foot pod powers off to

conserve the battery. When the battery is low, a message

appears on your device. Approximately five hours of battery life

remain.

Setting the Foot Pod Mode

You can set your device to use foot pod data instead of GPS

data to calculate pace and distance.

, wet the

Foot Pod Calibration

Calibrating your foot pod is optional and can improve accuracy.

There are three ways to adjust the calibration: distance, GPS,

and manual.

Calibrating Your Foot Pod by Distance

Before you can calibrate your device, you must pair your device

with the foot pod

For best results, the foot pod should be calibrated using the

inside lane of a regulation track or an exact distance. A

regulation track (2 laps = 800 m or 0.5 mi.) is more accurate

than a treadmill.

Calibrating Your Foot Pod by GPS

Data).

Before you can calibrate your device, you must acquire GPS

signals, and pair your device with the foot pod

Sensors).

Calibrating Your Foot Pod Manually

(Caring for the Heart

Before you can calibrate your device, you must pair your device

with the foot pod

Manual calibration is recommended if you know your calibration

factor. If you have calibrated a foot pod with another Garmin

product, you may know your calibration factor.

Hold MENU.

Select Settings > Sensors > Foot Pod.

Select an option:

• Select Indoor when you are training indoors without GPS.

• Select Always On when training outdoors, when your

GPS signal is weak, or when you lose satellite signals.

(Pairing ANT+

Hold MENU.

Select Settings > Sensors > Foot Pod > Calibrate >

Distance.

Select Start to begin recording.

Run or walk 800 m or 0.5 mi.

Select Stop.

Hold MENU.

Select Settings > Sensors > Foot Pod > Calibrate > GPS.

Select Start to begin recording.

Run or walk approximately 1 k or 0.62 mi.

The device informs you when you have traveled far enough.

(Pairing ANT+

Hold MENU.

Select Settings > Sensors > Foot Pod > Calibrate >

Manual.

Adjust the calibration factor:

• Increase the calibration factor if your distance is too low.

• Decrease the calibration factor if your distance is too high.

Sensors).

(Pairing ANT+

Sensors).