Garmin GPSMAP 8600 series Manual de instrucciones de instalación - Página 2
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Sistema de navegación Garmin GPSMAP 8600 series. Garmin GPSMAP 8600 series 9 páginas.
También para Garmin GPSMAP 8600 series: Manual de instrucciones de instalación (9 páginas), Manual de inicio rápido (6 páginas)
Imprimir página
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of all cables.
Mounting the Device
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
NOTE: To avoid potential damage to the powder coating, use
only the included screws to mount the device. Using screws
other than the ones included will void your warranty.
To avoid potential damage to the device during installation,
leave the protective blue bumper on the device during the
installation.
The included template and hardware can be used to flush mount
the device in your dashboard. There are three options for
hardware based on the mounting surface material.
• You can drill holes and use the included nut plates and
machine screws. The nut plates can add stability to a thinner
surface.
• You can punch holes, tap them to M4, and use the included
machine screws.
• You can drill pilot holes and use the included wood screws.
1
Trim the template and make sure it fits in the location where
you want to mount the device.
2
Secure the template to the selected location.
9
3
Using a 3.6 mm (
/
in.) drill bit, drill one or more of the holes
64
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4
Using a jigsaw or rotary tool, cut the mounting surface along
the inside of the solid line indicated on the template.
5
Place the device in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the device fits correctly in the cutout, ensure the
mounting holes on the device line up with the larger 7.2 mm
9
(
/
in.) holes on the template.
32
8
If the mounting holes on the device do not line up, mark the
new hole locations.
9
Based on your mounting surface, drill or punch and tap the
larger holes:
9
• Drill 7.2 mm (
/
in.) holes for the included nut plate and
32
machine screws.
• Drill pilot holes for the included wood screws, and skip to
step 19.
• Punch and tap M4 holes for the included machine screws,
and skip to step 19.
10
If using the nut plates, starting in one corner of the template,
place a nut plate
over the larger hole
9
The smaller 3.5 mm (
/
line up with the smaller hole on the template.
2
NOTICE
NOTICE
drilled in step 9.
in.) hole
on the nut plate should
64
9
11
If the smaller 3.5 mm (
line up with the smaller hole on the template, mark the new
location.
12
Repeat steps 10 and 11 for each nut plate.
9
13
Using a 3.5 mm (
/
in.) drill bit, drill the smaller holes.
64
14
Remove the template from the mounting surface.
15
Starting in one corner of the mounting location, place a nut
plate
on the back of the mounting surface, lining up the
large and small holes.
The raised portion of the nut plate should fit into the larger
hole.
16
Secure the nut plate to the mounting surface by fastening an
included M3 screw
through the smaller 3.5 mm (
hole.
17
Repeat steps 15 and 16 for each of the nut plates along the
top and bottom of the device.
18
If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with the attached weather caps.
19
Place the device into the cutout.
20
Secure the device to the mounting surface using the included
M4 screws
.
21
Carefully remove the rubber protective bumper.
22
Install the decorative bezel by snapping it in place around the
edges of the device.
Connection Considerations
When connecting this device to power and to other Garmin
devices, you should observe these considerations.
• The power and ground connections to the battery must be
checked to make sure they are secured and cannot become
loose.
• For easier routing, the cables may be packaged without the
locking rings installed. The cables should be routed before
the locking rings are installed.
• After installing a locking ring on a cable, you should make
sure the ring is securely connected and the o-ring is in place
so the power or data connection remains secure.
Connecting to Power
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
/
in.) hole on the nut plate does not
64
WARNING
9
/
in.)
64