AlkaWay UltraStream Manual del usuario - Página 3
Navegue en línea o descargue pdf Manual del usuario para Sistemas de filtración de agua AlkaWay UltraStream. AlkaWay UltraStream 6 páginas. Benchtop and undersink installation
También para AlkaWay UltraStream: Manual del usuario (4 páginas), Manual (20 páginas)
Imprimir páginaINSTALLATION STEPS
1. Remove existing aerator from your faucet.
2. Attach your Ultra diverter
to your faucet.
Take case not to twist the hose. (Also, a little Teflon plumbers'
tape may be needed).
If you need the hose to be shorter, unscrew the collar on the
diverter, remove the hose, and cut to preferred length.
Re-attach hose by inserting hose end into collar, pushing hose
onto diverter and screwing the collar tightly.
If your kitchen faucet's thread does not match our diverter,
please check whether any of the alternative attachment rings
provided with your ultraStream work and if not please contact
your dealer or go to our website at www.alkaway-international.
com/diverter.
3. TURN ON WATER
pull the diverter pin to divert flow into your UltraStream.
4. RUN THE ULTRASTREAM
for approximately 20 mins at around 1 litre per minute to
remove filter dust residues and fully soak the filter media.
Do not drink this water.
5. FLOW CONTROL
UltraStream's base has a mains pressure certified flow valve
inside of it. Insert 2 fingers and pull the base off. You can then
adjust the valve inside the base. The valve is a blue and white
plastic. You are aiming for a flow rate that will give you a pH of
around 9.5. This may take a few tries using the pH reagent to
check pH. Once set, this will ensure the same pH every time you
use it.
6. FIRST FLUSH
After installing the diverter, turn on the tap and let it run
through the UltraStream for at least 20 minutes. It may appear
discoloured due to carbon and other media 'fines' being flushed
out. Once output water clears, the filtered water may be
used directly for drinking, washing and cooking.
7. TURNING OFF
When you turn off flow at your faucet, filtered water
may still flow for 20-30 seconds. This is due to residual
pressure that may build up inside the UltraStream's
highly efficient filter. It will also drip for some time due to
the power of the hydrogen generation in the filter.
If unused for a few days, first use water may be slightly
grey and have a strong taste. This is caused by initial
output water soaking in the energising media ever since
you last used it.
Allow water to run for 1-3 minutes through the Ultra or
until it becomes clear once more.
pH TESTING
In your carton you'll find a pH Reagent bottle. Use the
dropper to test water from your UltraStream.
Do NOT consume the reagent or water with the reagent
in it. The colour on the test strip corresponds to the pH
of the water. The pH of your water is affected by (a) the
pH of your input water and (b) the rate of flow of the
UltraStream. There's little you can do about your source
water but you can adjust the pH by adjusting the flow
using the valve on the underside. We recommend a pH
of around 9.5 for best results, but because this is an
unbuffered pH, higher readings will not affect you.
Always taste to test for palatability. First days of use
may have a stronger taste.
UNDERSINK
INSTALLATION
The UltraStream has an excellent optional under-
sink installation kit. It includes a specially designed
ceramic faucet with special venting that ensures the
UltraStream is protected from high mains pressure
and water hammer. THIS FAUCET MUST BE USED.
Warranty on your system is void if you use a
different undersink faucet system.
Unqualified installation is also not guaranteed. Install
at your own risk.