Garmin GHP 10 Manual de instrucciones de instalación - Página 4
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Sistema GPS marino Garmin GHP 10. Garmin GHP 10 26 páginas. Autopilot system, addendum
También para Garmin GHP 10: Manual de instrucciones de instalación (48 páginas), Manual del usuario (28 páginas), Declaración de conformidad (1 páginas), Referencia (1 páginas), Notas de configuración (14 páginas)
Imprimir página
Cables and Connectors
The GHP 10 autopilot system includes multiple cables. These cables
connect the components to power, to each other, to an alarm, and to
optional devices.
CCu/ECu Interconnect Cable
This cable connects the CCU to the ECU. A portion of this cable
contains color-coded wires with bare ends. These wires connect the
CCU to the alarm and to the yellow wire from the GHC 10.
CCu/ECu Interconnect Extension Cables
When installing the GHP 10 system, you may need to mount the
CCU farther than 16 ft. (5 m) from the ECU. Garmin offers optional
replacement or extension cables for purchase if this is necessary.
type
Length
Replacement
32 ft. (10 m)
Replacement
66 ft. (20 m)
Extension
16 ft. (5 m)
Extension
50 ft (15 m)
Extension
82 ft. (25 m)
Contact your local Garmin dealer or Garmin Product Support for
ordering information.
alarm
The alarm provides audible alerts from the GHP 10
ECu Power Cable
This cable powers the ECU
(page
GHC 10 nMEa 0183 Data Cable
Included in the GHC 10 box, this cable connects the GHC 10 to the
yellow wire of the CCU, and to the same ground as the ECU
12). This cable can also be used to connect the GHC 10 to optional
NMEA 0183-compatible devices
4
(page
11).
10).
(page
(page
14).
nMEa 2000 Cables and Connectors
The NMEA 2000 cables connect the CCU and the GHC 10 to the
NMEA 2000 network. Either connect the CCU and the GHC 10 to an
existing NMEA 2000 network using the included T-connectors and drop
cables, or use all of the included NMEA 2000 cables and connectors to
build a NMEA 2000 network on your boat if needed
➊
➋
➌
➊ NMEA 2000 drop cable, 6 ft. (2 m) (×2)
➋ NMEA 2000 power cable
➌ NMEA 2000 T-connector (×3)
➍ NMEA 2000 terminator, male
➎ NMEA 2000 terminator, female
nMEa 2000 Extension Cables
NMEA 2000 extension cables are available if needed. Contact
your local Garmin dealer or Garmin Product Support for ordering
information.
External tachometer Filter
If your tachometer source is a direct alternator connection or other
signal larger than 12 Vdc, or if you sporadically receive tachometer
errors, install an external tachometer filter (Garmin part number: 010-
11399-00), not included. Contact your local Garmin dealer or Garmin
product support for ordering information.
tools needed
• Safety glasses
• Drill and drill bits
• 3
/
in. (90 mm) hole saw
1
2
• Wire cutters/strippers
• Phillips and flat screwdrivers
• Cable ties
• Waterproof wire connectors (wire nuts) or heat-shrink tubing and a
heat gun
• Marine sealant
• Portable or handheld compass (to test for magnetic interference
when determining the best location to install the CCU)
• Anti-seize lubricant (optional)
NOTE: Mounting screws are provided for the GHC 10, for the
CCU, for the ECU, and for the pump. If the provided screws are not
appropriate for the mounting surface, you must provide the correct
types of screws.
(page
12).
➍
➎
GHP 10 Installation Instructions