Flush Mounting the GPSMAP 3006C/3010C
Tools
• Flush Mount Template
• Jig saw
• Masking tape
• Scissors
• Drill
• Drill bits—1/8" (3 mm) and 3/8" (6 mm)
• 1/16" (2 mm) Allen (Hex) wrench
• Sockets or wrenches
• Hammer
• Center punch
To flush mount the GPSMAP 3006C/3010C:
1. Trim the Flush Mount Template, and tape it in the location you want.
2. Using the center punch, indent the center of each mounting hole location.
"
3. Using an 1/8
(3 mm) drill bit, drill the four mounting holes.
"
4. Using a 3/8
(6 mm) drill bit, drill a hole to begin cutting the mounting surface.
5. Using the jig saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a file and sandpaper to
refine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case
molding and the mounting holes.
6. Install the four mounting studs into the unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16
Allen wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage the
mounting stud! The studs have a reusable thread-locking patch
pre-applied from the factory.
7. Place the unit into the cut-out of the mounting surface.
8. Place washers over the mounting studs, then thread on one hex
nut per mounting stud. Tighten all four until the unit is snug against
the mounting surface. Install and tighten the second hex nut set on
all four mounting studs to lock the first set in place.
TRIM TEMPLATE ALONG THIS LINE TO AID FITTING
9.05" (230 mm)
GPSMAP 2010/2010C/3010C/3210
CUT MOUNTING SURFACE
ALONG INSIDE OF THIS LINE.
Be very careful when cutting this hole,
because there is only a small amount of
clearance between the unit and the
mounting hole.
To flush mount the GPSMAP 2010/2010C/3010C/3210:
1. Trim the flush mount template and tape in the desired location.
2. Using the center punch, indent the center of each mounting hole location.
3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. (Drilling the mounting
holes before cutting the hole for the unit allows for an easier installation.)
4. Using a 3/8" (6 mm) drill bit, drill a hole to begin cutting the mounting surface.
UNIT OUTLINE
5. Using the jig saw, cut the mounting surface along the inside of the dashed line
indicated on the template. Be very careful when cutting this hole, because there is only a
small amount of clearance between the case molding and the mounting holes.
6. Install the four mounting studs into unit by screwing the shorter, threaded section
into the back of the unit. Use a 1/16" (2 mm) Allen wrench to tighten the mounting studs
until the stop contacts the case. Be careful not to overtighten, because this may damage the
mounting stud! The studs have a reusable thread-locking patch pre-applied from the factory.
7. Place the unit into the cut out of the mounting surface.
8. Place washers over the mounting studs, and then thread on one hex nut per mounting stud.
Tighten all four until the unit is snug against the mounting surface.
Install and tighten the second hex nut on all four mounting studs to lock the first one
in place.
Drill a 3/8" (6 mm) hole.
Begin cutting here.
Flush Mount Template
GPSMAP 3006C/3010C & GPS 17
8.19"
(208 mm)
Flush Mount
Stud
Washer Hex nuts
I
I
NSTALLATION
NSTRUCTIONS
RANGE
PAGE
QUIT
ENTER
MARK
ADJ
NAV
MENU
MOB
DATA
CNFG
FCTN
FIND
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PQRS
TUV
WXYZ
7
8
9
+
-
0
"
(2 mm)
Mounting surface
3
Imprimir página